manualshive.com logo in svg

palintest Micro 800, Инструкция по эксплуатации

Поделиться
Скачать
palintest Micro 800 Скачать руководство пользователя страница 17

Micro 800 Optical DO Instruction Manual 

Rev 1 

© 2014 Palintest Ltd. 

www.palintest.com 

Page 17 of 41 

10. 

 Cleaning the Probe

 

The Sleeve on the Micro 800 Probe is easily removed by unscrewing to allow cleaning of 
the electrode. 
 
With the Sleeve removed, the electrode is very vulnerable, so please handle the Probe with 

extreme care. If you drop it, it’s going to 

break! 

 
Rinse the electrode and the inside of the Sleeve under a running cold tap.  
 
Alternatively, agitate the Probe vigorously in a bucket or jug of fresh water using an up and 
down movement.  
 
A soft cloth or toothbrush and some mild detergent may be used to remove stubborn dirt 
from the EC Sensor wires.  
 
It is especially important to keep the black rubber tip of the DO Cap clean, since organic 
fouling may consume oxygen which can affect DO measurements.  
 
To  clean  the  DO  Cap,  gently  wipe  away  any  fouling  with  a  soft  cloth  that  has  been 
moistened with fresh water. 
 
Dry the electrode using a soft cloth. Shake the water from inside the Sleeve, then reattach. 
Dry the outside of the Probe using a soft cloth.  
 

Never clean the any part of the Probe with solvents, alcohol or concentrated acid / 
alkaline based cleaning products such as Decon 90.  
 
These products can strip the anodised finish from the Probe and damage the plastic 
and rubber components. Damage caused by the use of aggressive cleaning agents 
or solvents is not covered by your warranty.  

 
 

TIP:

 Occasional application of a smear of silicone grease or similar lubricant to the Sleeve 

thread and O ring will make fitting and removal of the Sleeve easier. 
 

Содержание Micro 800










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды