Palazzetti ecopalex 64 страница 40 Скачать руководство пользователя

Страница: 40 / 124

00 477 0152 -04/2017 - PALAZZETTI - PN - I

TALY

INSTALLATION

overload the combustion chamber.

The recommended amount of wood is indicated in the
technical data table.

It is absolutely prohibited to use any kind of coal, wood
treated with protective substances, cardboard or paper
(use only for lighting).

It is prohibited to use the wood insert as an
incinerator. Burning of waste is prohibited in
compliance with laws concerning the emission of
gases. Combusted gases deriving from combustion

PD\UHVXOWLQGDPDJHWRWKHZRRGLQVHUWDQGWKHÀXH

and may be harmful to your health

7.2 LIGHTING

• Clean

the

replace from any ash residues;

•

completely open the primary air adjuster (

g.6.2 a/b);

• open

the

re door;

•

carefully place the wood pieces inside the combustion
chamber;

•

place a natural

re starter on the stack;

•

add some crossed

ne wood sticks;

•

light up the

re starter from the top

• close

the

re door

•

keep the air vent opened to ensure a high bright

ame

•

slightly close the air vent only when proper grill base
is ensured.

7.3

RELOADING THE FUEL

To load fuel inside the machine while it is running, follow
the procedure below:

• Open

the

re door slowly to prevent the creation of

an air gap inside the

replace that would cause the

smoke to escape in the environment (based on the
draught of the fume exhaust duct).

• Reload

the

replace with fuel and then close the

re door.

Avoid overheating the stove by loading an excessive
amount of fuel.

Insert the fuel only when the grill bases are formed

DQGWKHÀDPHLVORZ

The stove is provided with a bypass valve that favours
smoke transfer in the fume exhaust duct, minimizing the
smoke puffs in the environment

COMMISSIONING AND USING THE
APPLIANCE

The door should be opened gradually so the smoke can
be drawn up the

ue and not in the room. When lighting

the

replace, and until it reaches the right temperature,

it should burn for a few minutes with the door ajar so that
the condensation that forms on the glass can evaporate.
Once the

re is burning well, close the door to optimise

yield and consequently, wood consumption.

7.1

LIGHTING FOR THE FIRST TIME

•

Check that all moving parts are suitably placed and the
air control valve and smoke diaphragm work properly.

The

rst lighting (after the installation or at the beginning

of the season) must be made with reduced loads (~ 1
kg/h) keeping the device on for at least 4 hours at low
rate. Proceed with these feed rates for at least three days
before using the appliance at its full capacity. This will
allow for the evaporation of any moisture accumulated
in the refractory elements when not used.

• Light

the

re using old and

nely chopped wood so that

the

ame develops as much as possible. Once the

is going well you can use larger pieces of wood provided
they are dry.

The

rst time you light the

replace smoke and unpleasant

odours might form and escape due to the complete drying
of some of the materials used. This phenomenon will
gradually disappear.

•

FLUE DRAUGHT

•

Never use alcohol, petrol, kerosene or other liquid fuels
to light the

re. Keep these substances away from the

re. Do not use petrol or chemical origin

re-lighters

as they can seriously damage the walls of the

rebox.

Only use ecological

re lighting aids.

Do not touch the painted parts during the

rst lightings to

avoid damaging the paint

nish.

• During

the

rst lightings, we recommend that you keep the

premises well ventilated.

7.1.1 TYPE OF FUEL

The normative reference for fuel is UNI ISO 17225-1
“forest logs”.
The wood insert is to be fed preferably with mature beech
or birch wood or with lignite briquettes 25 or 33 cm.

Humidity must not exceed 25%.
Each type of wood has different characteristics that also

uence combustion yield.

Use of pine-wood (pine,

r) is not recommended as it

contains high quantities of resin substances that quickly
clog the

ue.

It is forbidden to burn: pieces of bark, wood treated with
varnish, pressed wood panels, coal, plastic materials; in
this case, the guarantee on the wood insert is no more
valid.

The declared nominal yield of the chimney is obtained
by burning the right quantity of wood, making sure not to