manualshive.com logo in svg

paladin FFC LAF5647, Руководство оператора и каталог запасных частей

Поделиться
Скачать
paladin FFC LAF5647 Скачать руководство пользователя страница 17

MR25661

14

POWER RAKE MAINTENANCE 

GENERAL INFORMATION

 

Regular maintenance is the key to long equipment life and safe operation.  Maintenance requirements 

have been reduced to the absolute minimum.  However, it is very important that these maintenance functions be 

performed as described below.

1. 

Park your prime mover on a level surface with this product properly attached.

2. 

Place your prime mover’s transmission in “Park” and engage the parking brake.

3. 

Lower this product onto preplaced blocking.

4. 

Shut off your prime mover’s engine, remove the starter key, wait for all moving parts to come to a stop,  

 

and relieve all pressure in the hydraulic lines (refer to your prime mover's operator's manual for 

 

instructions on how to relieve hydraulic pressure).  On PTO drive models disconnect the driveline.

WARNING!

 

Do not use blocking made of concrete blocks, logs, buckets, barrels or any other    

 

 

material that could suddenly collapse or shift positions. Do not use wood or steel

 

 

blocking that is warped, twisted, or tapered. Failure to obey this warning could result in  

 

 

death or serious injury.

BEFORE EACH USE

•

 

Make sure all shielding is in place.

• 

On PTO drive models check driveline for wear.

• 

Make sure that all nuts and bolts are in place and properly tightened.

• 

Make sure that all other fasteners are in place and are performing their specified function.

• 

Make sure that tires are inflated to maximum load pressure indicated on tire. Do not over inflate.

• 

Make sure that all hydraulic fittings are tightened to specifications and that there are no leaks in any  

 

fittings or hoses. (SEE THE HYDRAULIC CONNECTION SECTION).

• 

Make sure that all safety signs are in place, are clean, and are legible.    

 

 

 

 

(SEE THE SAFETY SIGN SECTION).

• 

Replace any damaged parts and excessively worn parts.

AFTER EVERY 10 HOURS OF USE ON PTO DRIVE MODELS

• 

Grease roller bearing (48” and PTO drive models only).  Grease all u-joint cross bearings.   

 

 

The main frame shaft guard must be removed to grease the hex driveline.

WEEKLY

• 

Lubricate all pivot points, PTO driveline guard, and PTO driveline telescoping shafts.

FOR PTO DRIVE – AFTER 50 HOURS OF USE AND THEN EVERY 1000 HOURS OR ANNUALLY

• 

Drain the 90 degree gearbox and the spur gear case of lubricant and refill with 80-90 W gear lube with  

 

an EP rating of GL-5 minimum.  (Approximately 41 oz. For the 90 degree gearbox and 63 oz. For the  

 

spur gear case.)

ANNUALLY

Repack the bearings in the wheels as described in steps 1-4 below.

1. 

Make sure that there is no weight on the wheels.  If the wheels are partially supporting the weight of this  

 

product, restart your prime mover and move the loader and/or dump cylinders.  Repeat the specified  

 

shutdown procedure.

2. 

Remove each wheel using two wrenches and remove the bearing components from the wheels.

3. 

Clean the bearing components, and then use a high quality waterproof grease to repack the bearing  

 

components & hub.

4. 

Reassemble all components using a new seal.

 

Содержание FFC LAF5647




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды