background image

Section 150-619-100

Revision 01

Page 17

TABLE 3.  HLU-619 FOUR-CHARACTER FRONT PANEL MESSAGES (CONTINUED)

M

ESSAGE

F

ULL 

N

AME

D

ESCRIPTION

PWR FEED SHRT

Power Feed Short

Indicates a short between the VHDSL conductors.  This same

message can occur with an HRU, which is drawing the correct
amount of power over good cable pairs, but cannot communicate
with the HLU.

PWR FEED OPEN Power Feed Open

Indicates an open circuit in the T and R of either VHDSL pair.

PWR FEED OFF

Power Feed Off

VHDSL span power has been turned off by setting the PWFD option

to DIS.

BAD RT?

No response from
HRU

The HLU does not receive any response from the HRU.  The HRU’s
integrity is questionable.

VER XXXX

HLU software Version
number

Displayed during the System Settings review mode.  Press the Mode
button for 3 seconds.

LIST XXXX

HLU’s List number

Displayed during System Settings review mode defined above.

FRM

Frame:  SF, ESF,
UNFR, None

Defines the type of frame pattern being received from the DSX-1.
Displayed during System Settings review mode defined above.

CODE

Line Code:  AMI,
B8ZS

The line code that the HLU-619 is receiving at its DSX-1 interface, if
the DS1 option is set to Auto.  Otherwise, it mimics either of the
other two DS1 line code settings, AMI or B8ZS.  Displayed during
System Settings review mode defined above.

LOSW

Loss of Sync Word

Indicates that the VHDSL loop has lost sync.  Causes a minor alarm.

LLOS

Local Loss of Signal

Indicates that no signal is detected at the DSX-1 input to the HLU.

Causes a minor alarm.

RLOS

Remote Loss of
Signal

Indicates that no signal is detected at the DS1 input to the HRU.
Causes a minor alarm.

DS1

DS1 BPV Errors

Indicates that the number of BPVs at the HLU or HRU T1 inputs
have exceeded the 24-hour ES threshold.  Causes a minor alarm.

DS0

DS0 Blocked
Channels

Indicates status of DS0 blocked channels.  “None” indicates no
channels are blocked.  BLK indicates some channels are blocked.

MAL

Margin Alarm Loop

The margin on the VHDSL loop has dropped below the threshold (0
to 15 dB) set by the user.

MNGD

Managed

The HLU-619 is under control of the HMU-619 network management
unit.  In this state, the RS-232 maintenance port on the HLU-619
front panel is inoperative.

Содержание HIGAIN-2 HLU-619




































Отзывы: