Pacific Scientific OC950 EPROM Скачать руководство пользователя

Страница: 8 / 87

OC950 Hardware

Varieties

Two optional memory (NVRAM: nonvolatile random access
memory) configurations are available, 32kx8 or 128kx8. NVRAM
is battery backed, with a ten year life, and unlimited amount of
write cycles. The memory provides storage for the user programs.

A PacLAN



Network interface is offered as an OC950 option.

PacLAN supports 2.5 Mb/sec communications between a cluster
of SC950 drives. The port will be compatible with standard
ArcNET products using 93

Ω

coax cable in a bus configuration.

Standard

version

Combinations of the two memory offerings and the PacLAN
option results in four standard versions of the OC950:

OC950-501-01

Base 950 Option Card 32kx8 NVRAM

OC950-502-01

Base 950 Option Card 128kx8 NVRAM

OC950-503-01

Base 950 Option Card 32kx8 NVRAM + PacLAN

OC950-504-01

Base 950 Option Card 128kx8 NVRAM + PacLAN

Enhanced

Version

In addition, there is an Enhanced version of the OC950 which
supports additional features, including MODBUS and camming.

OC950-601-01

Enhanced 950 Option Card 32kx8 NVRAM

OC950-602-01

Enhanced 950 Option Card 128kx8 NVRAM

OC950-603-01

Enhanced 950 Option Card 32kx8 NVRAM + PacLAN

OC950-604-01

Enhanced 950 Option Card 128kx8 NVRAM + PacLAN

1 - 2

MA950

Содержание OC950 EPROM
























































































Результаты поиска

Содержание OC950 EPROM

Отзывы:

Похожие инструкции для OC950 EPROM

Бренды по названию

Популярные бренды

Pacific Scientific OC950 EPROM, Руководство по установке и аппаратным средствам

Результаты поиска

Содержание OC950 EPROM

Отзывы:

Похожие инструкции для OC950 EPROM

Бренды по названию

Популярные бренды