manualshive.com logo in svg

Pacific Living PL8304SS, Руководство пользователя

Поделиться
Скачать
Pacific Living PL8304SS Скачать руководство пользователя страница 28

 

 

28 

WARNING 

Heat and smoke exhaust out of

 

the chimney and the ventilation holes on the bottom 
of two oven side panels (See Fig. 8).

 

Make sure to 

keep anything that could be damaged by heat or 
smoke away from the heat and smoke exhaust 
holes. 

 
 
GENERAL RULES 
Do not leave the oven unattended while cooking! 

1. Make sure the oven has been leak-tested and is properly located. 
2. Light the oven burners using the instructions provided in this manual. 
3. Turn the control knobs to desired temperature - High or Low - and preheat the oven for 10 
minutes before cooking. 
4. Adjust heat settings to meet your cooking needs for desired results. 
5. Allow oven to cool down, wipe off any splatters or grease and clean the drip tray as needed. 
6. Do not put a cover on the oven while it is still hot as it could start a fire.   
 

 

 

BEFORE AND AFTER LIGHTING 

1. Ensure your oven is located on a level surface. 
2. Keep the gas oven area clean and free from combustible materials, gasoline, and other 
flammable vapors and liquids. 
3. Ensure nothing is obstructing the flow of combustion and ventilation air. 
4. Ensure the ventilation of the cylinder enclosure is free and clear of debris. 
5. Visually check burner flames.

 

 

WARNING 

Check the gas supply line for cuts, wear or abrasion. 

Always keep your face and body as far away from the oven as possible when lighting. 
 

Do not attempt to “light” the oven if the odor of gas is 
present!! 

Содержание PL8304SS
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды