Pacific energy trenton A series Скачать руководство пользователя

Страница: 32 / 40

5055.45-A 021115-40

TRNT.BODYA

Installer information

Servicing of the gas stove can be performed from the rear of the unit by removing the

access panel from the unit.

Caution:

The gas line should be installed by a qualified service person in accordance

with all building codes. This section is intended as a guide for qualified

technicians installing this gas stove. Consult local and/or national building

codes before proceeding.

•

Gas supply line connection is located on the rear of the gas stove. Gas

connection accepts a

⅜” 45° flare fitting. Correct gas line diameter must be

used to assure proper operation and pressure.

•

The gas stove input rating is shown in the chart below.

•

A drip leg must be installed in the gas supply line going to the gas control valve

to minimize the possibility of any loose scale or dirt within the gas supply line

from entering the control valve.

•

It is essential that a union or flanged connection (not provided) be installed just

upstream of the valve to allow for repair or replacement of the gas valve.

Check local codes for additional requirements.

Turn on the gas supply and check that all connections are tight and leak free.

Gas pressure requirements

Input Pressure

Natural Gas Propane

Minimum 5.0” WC

12.5” WC

Maximum

13.9” WC

Manifold Pressure

High

3.8” WC

11” WC

Low

1.1” WC

2.9” WC

Trenton

Gas Orifice Output

AFUE

2.26 mm 24,000 btu/hr 73.0%

1.40 mm 24,000 btu/hr 73.0%

Gas Supply

Gas Pressure Check

Содержание trenton A series









































Результаты поиска

Содержание trenton A series

Отзывы:

Похожие инструкции для trenton A series

Бренды по названию

Популярные бренды

Pacific energy trenton A series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание trenton A series

Отзывы:

Похожие инструкции для trenton A series

Бренды по названию

Популярные бренды