Pacific energy trenton A series Скачать руководство пользователя

Страница: 1 / 40

WARNING: If the information in these

instructions is not followed exactly, a fi re

or explosion may result causing property

damage, personal injury or death.

This appliance may be installed in an aftermarket

permanently located, manufactured home (USA only)

or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless a

certifi ed kit is used.

This appliance is suitable for installation in a

bedroom or bed sitting room.

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

TRENTON

MODEL: TRENTON
SERIES: A
FREESTANDING GAS STOVE
INSTALLATION AND OPERATING
INSTRUCTIONS

021115-40

5055.45-A

SERIAL #

TRNT.BODYA

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious

injury, death, or property damage.

- Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone

in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a neighbour’s phone.

Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier call the fire department.

- Installation and service must be performed by a qualified

installer, service agency or the gas supplier.

Visit www.pacifi cenergy.net for the most up-to-date version of this manual

Содержание trenton A series









































Результаты поиска

Содержание trenton A series

Отзывы:

Похожие инструкции для trenton A series

Бренды по названию

Популярные бренды

Pacific energy trenton A series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание trenton A series

Отзывы:

Похожие инструкции для trenton A series

Бренды по названию

Популярные бренды