Pacific energy TOFINO i30s Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 44

background image

Electrical Supply

Gas Supply

Figure 34: Electrical connection.

Figure 35: Toﬁno gas connection.

Note: Installation (SIT units only. See “Existing Fireplace
Preparation” on page 9) requires that an electrical out-
let be installed into existing ﬁreplace cavity before insert is
installed.

NOTE: The appliance, when installed must be electrically
grounded in accordance with local codes or, in the absence of
local codes, with the National Electrical Code, ANSI/NFPA 70,
or the Canadian Electrical Code, CSA C22.1.

Caution: The gas line should be installed by a qualiﬁed service person in accordance with all building codes.

This section is intended as a guide for qualiﬁed technicians installing this appliance. Consult local and/or

national building codes before proceeding.

r

Gas supply line connection is located on the left rear side of the insert (Figure 35). Gas connection
accepts a 3/8” N.P.T. ﬁtting. Correct gas line diameter must be used to assure proper operation and pres-

sure.

Do not use external threads for gas connections. Use internal threads only.

r

A drip leg must be installed in the gas supply line close to the appliance to minimize the possibility of any

loose scale or dirt within the gas supply line from entering the control valve.

Check local codes for additional requirements.

Turn on the gas supply and check that all connections are tight and leak free.

To gas valve assembly

Figure 36: Gas shut off valve.

19

5055.990-A

130717-44

i30 TOFINO

«
...
17
18
19
20
21
...
»

Содержание TOFINO i30s













































Отзывы:

Нет отзывов

Похожие инструкции для TOFINO i30s

CLEARion Series

Бренд: Napoleon Страницы: 30

Бренд: DS Produkte Страницы: 2

Бренд: UC Living Страницы: 28

Бренд: Paramount Fitness Страницы: 14

Бренд: Home Decorators Страницы: 20

Бренд: Riello Страницы: 80

OUTLAND FIREBOWL FMPPC2-2

Бренд: FMI Страницы: 8

Бренд: Febo Страницы: 16

Бренд: kozy heat Страницы: 51

Бренд: Napoleon Страницы: 80

Astound-Built In Series

Бренд: Napoleon Страницы: 80

Бренд: glamour Страницы: 12

Бренд: baltur Страницы: 72

Бренд: IHP Страницы: 2

Бренд: Flavel Страницы: 42

Бренд: Flash Furniture Страницы: 6

Corner Right & Left 120

Бренд: Flare Fireplaces Страницы: 86

Бренд: Majestic fireplaces Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды