Pacific energy TOFINO i30s Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 44

background image

3” Air intake

4” Exhaust

Figure 10: 4 x 3 inch Flue adapter.

Depending on the amount of room available for the installation of the Toﬁno, the installer may want to remove
the ﬂue adapter and attach it to the ﬂex tubes which will have previously been inserted down the chimney.

The installer must make sure that the air intake vent and air exhaust vents attach to the correct ports on

both the ﬂue adapter and the vent terminal. The vent terminal and the ﬂue adapter are marked with an “I” (air
intake) and “E” (air exhaust).

Venting

10’ to 40’ Use the 3x4 Conﬁguration

10’ to 28’ Use the 3x4 and the 4” to 3” adapter Conﬁguration

The i30 comes from the factory with a 3” intake and a 4” exhaust conﬁguration. Whenever possible, this

conﬁguration should be used. However, a 4” to 3” optional reducer (Figure 11) can be used on the exhaust
for venting lengths between 10’ and 28’ if necessary. Be advised that using this optional adapter may have
an impact on ﬂame appearance and is not recommended for use with the glass burner option while operat-
ing with propane gas.

Installation Advisory

Installation Tip

Figure 11: 4 inch to 3 inch

exhaust adapter.

Optional 4” to 3” exhaust adapter

Part number for the optional 4” to 3” exhaust adapter is 1227.0003.

12

130717-44 5055.990-A

i30 TOFINO

«
...
10
11
12
13
14
...
»

Содержание TOFINO i30s













































Отзывы:

Нет отзывов

Похожие инструкции для TOFINO i30s

Бренд: barkman Страницы: 16

CROSSOVER CO10-101-M

Бренд: Magma Страницы: 18

Бренд: Valor Страницы: 60

Бренд: Comfort Flame Страницы: 70

HKI Leo 28/9251

Бренд: Olsberg Страницы: 37

Бренд: Napoleon Страницы: 2

purview 42 Series

Бренд: Napoleon Страницы: 128

Бренд: Amantii Страницы: 18

Бренд: Valor Страницы: 14

Бренд: Rinnai Страницы: 20

Бренд: Napoleon Страницы: 136

Бренд: KEKAI Страницы: 46

Бренд: Pacific energy Страницы: 28

Бренд: Uberhaus Страницы: 7

Бренд: HAMPTON BAY Страницы: 36

Apollo Crea7ion.E Series

Бренд: GlammFire Страницы: 16

Бренд: Home Depot Страницы: 24

Бренд: Home Decorators Collection Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды