Pacific energy SUMMIT WOOD INSERT DESIGN-A Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 20

Pacific energy SUMMIT WOOD INSERT DESIGN-A Скачать руководство пользователя страница 8

8

SUMINSERTA 160309-20

10) Position the decorative bay stove top onto the firebox top.

Ensure that the studs align with the slotted tabs, one on
each side of the firebox top. Secure in place with 1/4”
nuts provided.

11) Replace the front panels and ashlip in the reverse order

to their removal.

8) Slide pre-assembled surround into the friction fit tabs

on the inside of the outer casing.  DO NOT LIFT THE
SURROUND ASSEMBLY BY GRASPING THE TRIM.
The surround is held in place by four screws, two each
side, just inside the casing near the top and bottom.  Push
surround back until snug and even. Fasten in place.

9) Push the entire appliance back until the surround as-

sembly is in contact with the fireplace.

7) Remove the two screws which were concealed by the

ashlip and two screws near the top from the left and right
panels. Remove front panels and set aside to prevent
damage.

Fig. # 10

Fig. # 13

Fig. # 11

Fig. # 12

«
...
6
7
8
9
10
...
»

Содержание SUMMIT WOOD INSERT DESIGN-A





















Отзывы:

Нет отзывов