PACIFIC FP30 190712-28
3
Safety and
Maintenance
1.
Burn only, dry and well seasoned cord wood.
The
denser or heavier the wood when dry, the greater its heat
value. This is why hardwoods are generally preferred.
Green or wet wood should not be used, it will reduce heat
output, as well as, contributing signifi cantly to creosote
buildup.
WARNING: NEVER USE CHEMICALS OR ANY OTHER
VOLATILE LIQUID TO START A FIRE. DO NOT BURN
GARBAGE OR FLAMMABLE FLUIDS SUCH AS
GASOLINE, NAPHTHA, OR ENGINE OIL. WE STRONGLY
RECOMMEND THAT SMOKE DETECTORS BE
INSTALLED.
2. Remove ashes frequently. Embers can roll out the door
and create a fi re hazard. Maintain a 1" minimum ash
base.
3. The area where boost combustion air enters the fi rebox
must be kept clear of excessive ash buildup which will
block air fl ow. This area is at the front of the fi rebox.
4. If glass becomes darkened through slow burning or poor
wood, it can be cleaned with fi replace glass cleaner when
the stove is cold. Never scrape with an object that might
scratch the glass. The type and amount of deposit on the
glass is a good indication of the fl ue pipe and chimney
buildup. A light brown dusty deposit that is easily wiped off
usually indicates good combustion and dry, well-seasoned
wood and therefore relatively clean pipes and chimney.
On the other hand, a black greasy deposit that is difficult
to remove is a result of wet and green wood and too slow
a burning rate. This heavy deposit is building up as quickly
in the chimney.
5. Establish a routine for the fuel, wood burning and fi ring
technique. Check daily for creosote buildup until experi-
ence shows how often you need to clean to be safe.
WARNING: ONLY USE MATERIALS AND COMPONENTS
SUPPLIED OR SPECIFIED BY MANUFACTURER WHEN
DOING MAINTENANCE OR REPLACEMENTS. DO NOT
USE A FIREPLACE INSERT TO OTHER PRODUCTS NOT
SPECIFIED FOR USE WITH THIS FIREPLACE.
6. DOOR GASKETS - The gasket used by Pacifi c Energy
(7/8" medium density fi breglass rope) requires only light
pressure to seal. This will prolong seal life. It is impor-
tant that the door seal be maintained in good condition.
Periodically inspect seals and replace if necessary. 7.
DOOR GLASS - Replacement glass can be obtained
from your dealer. Use 11 3/8" x 21 5/8" x 5 mm.
WARNING: DO NOT SUBSTITUTE GLASS WITH ANY
OTHER TYPE MATERIAL OTHER THAN CERAMIC
GLASS
WARNING: DO NOT SLAM LOADING DOOR OR OTHER-
WISE IMPACT GLASS. WHEN CLOSING DOOR, MAKE
SURE THAT NO LOGS PROTRUDE TO IMPACT THE
GLASS. IF THE GLASS GETS CRACKED OR BROKEN,
IT MUST BE REPLACED BEFORE USING THE STOVE.
WARNING: OVER FIRING THE APPLIANCE WILL SHORT-
EN THE LIFE OF THE PRODUCT. FAILURE TO RECTIFY
AN OVER FIRING CONDITION CAN BE HAZARDOUS AND
MAY VOID THE MANUFACTURER'S WARRANTY.
To remove broken glass,remove the door gasket and clean out
the screw heads. Remove the screws that hold the retainers
and remove the retainers, noting position for re-assembly.
Remove all particles of glass . Be careful as they are very
sharp. Install new glass complete with gasket. Replace
retainers, screws and gasket.
CAUTION:
- DO NOT OVERTIGHTEN, TIGHTEN SCREWS HAND
TIGHT
- DO NOT CLEAN GLASS WHEN HOT
- DO NOT USE ABRASIVE CLEANERS ON GLASS
8. Do not store wood within heater installation clearances, or
within the space required for fuel loading and ash removal.
Keep the area around the heater clean and free of loose
combustibles, furniture, newspapers, etc.
9. Be aware that the hotter the fi re, the less creosote is
deposited. Weekly cleaning may be necessary in mild
weather, even though monthly cleaning is usually enough
in the coldest months when burning rates are higher.
10. Instruct all members of your family on the safe operation
of the heater. Ensure they have enough knowledge of the
entire system if they are expected to operate it. Stress the
section on chimney fi res and the importance of following
the steps outlined "In Case of Chimney Fire".
11. Inspect and clean your chimney system at the beginning
of the burning season before your fi rst fi re and at least
every two months during the burning season. Inspect
the interior and exterior of the pipe for defects and/or
damage. Remove and inspect the rain cap. Refer to the
chimney system manufacturer's installation instructions
for the procedure to remove and or replace any necessary
components to the chimney system.
12. Maintain a distance of 30" to all combustible materials in
the room.
(see Floor Protection for Floor Protection dimensions)
