manualshive.com logo in svg

Pacific energy NEO 1.6 INSERT, Инструкция по установке и эксплуатации, Страница: 10 / 24

Поделиться
Скачать
Pacific energy NEO 1.6 INSERT Скачать руководство пользователя страница 10

10  

040515-24

©PACIFIC ENERGY FIREPLACE 
PRODUCTS LTD.

Warning: 

Under no circumstances is this heater to be installed 

in a makeshift or "temporary" manner. It may be fi red only 
after the following conditions have been met.

*   DO NOT ATTEMPT TO CONNECT THIS HEATER TO 

ANY AIR DISTRIBUTION DUCT.

*   Outside combustion air or fresh air into the room may be 

required in your area, consult local building codes (see 
Combustion Air section).

- The services of a competent or certifi ed installer, (certifi ed 
by the Wood Energy Technical Training program (WETT) - in 
Canada, Hearth Education Foundation (HEARTH) - in U.S.A.,) 
are strongly recommended.

BOTH CHIMNEY SYSTEM AND CONNECTOR MUST BE 
LISTED TO:  IN CANADA -  ULC S-641 LISTED CONNEC-

IN CANADA -  ULC S-641 LISTED CONNEC-

TOR AND ULC-S-629 LISTED CHIMNEY, 

TOR AND ULC-S-629 LISTED CHIMNEY, 

IN USA -  UL-103 

IN USA -  UL-103 

HT LISTED CONNECTOR AND CHIMNEY

HT LISTED CONNECTOR AND CHIMNEY

Clearances

1.  This heater may be installed using a single-wall connector 

(smoke pipe) or listed double-wall connector (see Mobile 
Home installation).

2.  Clearances to combustible surfaces and materials using 

single-wall connector are shown in Figure #7, page 12.

 

Clearances may be reduced with various heat insulating 
materials. Consult local fi re codes and authorities for ap-
proval.

3.  Alternately, for close clearances, use a listed double-wall 

connector.  See Fig #6, page 12.

It is possible to store wood between the stove supports, un-
derneath the unit. The wood must not extend further forward 
than fl ush with the supports. Do not store paper or othe stove 
lighting devices within the pedestal area. Although this is pos-
sible it is not recommended. NOTE: Refer to local fi re codes, 
CAN-B365 and NFPA 211 in the U.S..

WARNING: IF YOU CHOOSE TO STORE WOOD BENEATH 
YOUR UNIT, EXERCISE EXTREME CAUTION WHEN LOAD-
ING THE WOODSTOVE. EMBERS CAN FALL AND MAY 
IGNITE WOOD BENEATH STOVE.

Chimney and Connector

Connect to a listed chimney or a chimney suitable for use 
with solid  fuel that is lined and in good condition and meets 
local building codes. The chimney fl ue size should be the 
same as the stove outlet for optimal performance. Reduc-
ing or increasing the fl ue size may adversely affect stove 
performance. Chimney fl ue exit is to be 3 feet (1 m.) above 
roof and two feet (0.6 m.) above highest projection within 10 
feet (3 m.). The installation must meet all local codes. Do not 
connect this unit to a chimney fl ue serving another appliance. 
Minimum system height is 15 feet (4.6 m.) (measured from 
base of appliance).

Double-Wall Connector

- 

Use a listed double-wall connector.

- 

Install all components to the chimney connector manu-
facturer's installation requirements.

Single-Wall Connector

Smoke pipe must be:
*   as short and straight as possible, use six inch 
 

diameter, 24 gauge black pipe that is clean and in new 
condition.

*    secured at every joint and collar with 3 sheet metal screws.
*   installed with the crimped or male ends pointing down.  

This will carry any liquid creosote or condensation back 
into the stove.

*    The chimney connector shall not pass through an attic, roof 

space, closet or similar concealed space, fl oor, or ceiling.  
Where passage through a wall, or partition of combustible 
material is desired, the installation shall conform to CAN/
CSA-B365, Installation Code for Solid-Fuel-Burning Appli-
ances and Equipment or in the U.S., NFPA 211: Standard 
for Chimneys, Fireplaces, Vents, and Solid Fuel-Burning 
Appliances.

Procedure

1.  If a listed chimney and double-wall connector is to be 

connected to the stove, install all components to the chim-
ney manufacturer's installation requirements.  (Outside 
combustion air may  be required, consult local building 
codes.  See Combustion Air section on page 10.)

2.  If it is desirable to use smoke pipe in conjunction with the 

insulated chimney, see step 4.

3.  If a roof or ceiling support is used in the installation, you 

will fi nd the chimney manufacturer's complete instructions 
packed with the roof support.

4.  To start installing smoke pipe (chimney connector), slip 

crimped edge of the pipe inside the stove collar.  Use 
holes provided in collar to secure pipe with three screws.

5.  Install the remaining lengths of pipe one on top of the 

other to the fi nished height of the chimney connector and 
secure to each other.

Residential Installation

Содержание NEO 1.6 INSERT

























Отзывы:

Нет отзывов