background image

2

SAFETY INFORMATION

This digital set-top has been manufactured and tested with your safety in 
mind. However, improper use can result in potential electric shock or fire 
hazards. To avoid defeating the safeguards that have been built into your 
set-top, please observe the precautions discussed in this document.

To reduce the risk of fire or electric shock, do not expose this set-top to rain 
or moisture.

On the rear panel of your set-top there is a tamper-evident label that states 
‘Warranty void if broken or removed’.

To avoid possible damage to the internal hard disk, do not pick up or move 
your set-top while it is connected to the wall AC outlet. If you want to move 
your set-top, first stop any recording, then turn off your set-top and wait 60 
seconds before disconnecting it. You should handle your set-top carefully, as 
any damage you cause to the internal hard disk (or any other component) will 
invalidate your warranty.

Installation

The installation of your set-top should be carried out by a qualified installer 
and should conform to local codes.

Note to the installer

This reminder is provided to call the attention of the cable-TV-system 
installer to Section 820 of the National Electrical Code (USA), which 
provides guidelines for proper grounding and, in particular, specifies 
that the cable ground shall be connected to the grounding system of the 
building, as close to the point of cable entry as is practical.

Service address: 
Pace Americas Inc. 
3701 FAU Boulevard, Suite 200, Boca Raton, Florida 33431 U.S.A.

Other warnings

To reduce the risk of electric shock, do not remove the cover of your set-top.  
There are no user-serviceable parts inside it.

Do not perform any servicing unless you are qualified to do so. Refer all 
servicing to qualified service personnel. Servicing the set-top yourself will 
invalidate the warranty.

The lightning flash with arrowhead symbol, within a triangle, 
is intended to alert you to the presence of uninsulated 
“dangerous” voltages within your set-top’s enclosure that may 
be of sufficient magnitude to constitute a risk of electric shock 
to persons.

The exclamation point within a triangle is intended to alert 
you to the presence of important instructions in the literature 
accompanying your set-top.

Warnings on your set-top

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

ATTENTION

Содержание TDC780X

















































Отзывы: