background image

©2018 PACE Inc., Vass, North Carolina, All Rights Reserved                                                           Page 5 
 

 

Digital LED Display - Normal Operation 

 

The Digital LED Display provides a 3-digit display of information. The LED Display can show: 
 

1.  "888" on initial power up to ensure that all sections of the display are working. 

2.  The software version of the installed microprocessor (e.g., "1-9") for 2 seconds on initial power up after 

the "888" is displayed. 

3.  Actual temperature of the connected handpiece, during normal operation. 

4.  The temperature displayed will flash and the LED indicator will be off when the system is in 

Temperature SetBack mode. 

5.  "OFF" with stable display when the Set Temperature has been set below the minimum lower 

temperature limit. 

6.  "OFF" with flashing display when the unit has entered AutoOff mode. Refer to page 8 for more 

information. 

7.  Error messages ("CHP", "SSE" or "OCE") if a system fault is detected. Refer to the "Corrective 

Maintenance" portion of this manual. 

 
Digital Display - Temperature Adjust Mode 

 

The LED Display will show the following when adjusting the desired Set Tip Temperature. 
 

1.  The Set Tip Temperature. 

2.  "HiL" (High Temperature Limit) when adjusting the set tip temperature and the 

maximum allowable temperature is exceeded. Refer to the "Set-Up Mode" portion 
of this manual.

 

 

3.  "OFF" (Low Temperature Limit) when adjusting the set tip temperature and the 

minimum allowable temperature is exceeded. Refer to the "Set-Up Mode" portion 
of this manual.   

 

Default Factory Settings 

 
The ADS200 system comes equipped with a number of features, which may be adjusted by the user. Listed 
below are the default settings of each. To change and/or learn about any of these features, refer to the 
applicable part of the “Customizing Your System” section of this manual. 
 
 

Feature 

Factory Setting 

 

Feature 

Factory Setting 

Password 

None Entered 

 

Preset 1 

343°C (650°F) 

°F for 115 VAC Systems 

 

Preset 2 

371°C (700°F) 

Default Temperature 

Scale (°C/°F) 

°C for 230 VAC Systems 

 

Preset 3 

399°C (750°F) 

“HI” Temperature Limit 

427 °C (800 °F) 

 

SetBack Temperature 

176°C (350°F) 

“LO” Temperature Limit 

260 °C (500 °F) 

 

Temperature Match Mode 

“0C0” 

SetBack Timer 

Enabled, 30 minutes 

 

Set Temperature 

371°C (700°F) 

Auto Off 

Enabled, 60 minutes 

 

Temperature Match Value 

“0” 

Instant SetBack Timer 

Enabled, 30 seconds 

 

 

 

Содержание ADS200















Отзывы: