background image

 
 
 

3.  Set Upper Limit

  

Press the   UP and DOWN 

 to set the upper temperature limit. 900°F is the upper limit for 

SensaTemp handpieces. The Upper limit for TempWise handpieces is 850°F. Press and release the 
PROGRAM Key 

 to move to the next step. The upper limit feature will limit the temperature range 

that an operator may work within. Setting a password will lock out unwanted changes to this feature. 
 

4.  Set Low Limit

  

Press the   UP and DOWN 

 to set the upper temperature limit. 100°F is the upper limit for 

SensaTemp handpieces. The Upper limit for TempWise handpieces is 500°F. Press and release the 
PROGRAM Key 

 to move to the next step. The lower limit feature will limit the temperature range 

that an operator may work within. Setting a password will lock out unwanted changes to this feature. 
Adjusting the working temperature below the set lower limit will turn power off to the selected channel. 

 

5.  SetBack Time  

Choose one of the following: 
a)   Press and release the PROGRAM Key 

   

to keep the currently stored Temperature Setback 

time. 

b)   Press and release the Scroll 

 

UP Key to enable or increase the stored Temperature Setback 

time. Press and release the PROGRAM Key 

 

to proceed to the next step. Set back may be 

disabled by entering (00).  The maximum set back time is 90 minutes. 

c)  Press and release the Scroll Down Key to decrease or enter “00” to disable the stored 

Temperature Setback time. Press and release the PROGRAM Key  

 

 to proceed to the next 

step. 

The LED Display now shows the stored Temperature Setback time in minutes 

 

6.  Set Auto Off 

Press the 

 

UP Key to enter increase the auto-off time. When enabled, the Auto Off safety system of 

the MBT 350 system turns off the power to the Handpiece 10- 90 minutes after entering Temperature 
Setback. When the system has entered Temperature Setback, an Auto Off timer within the system 
circuitry will start running if Auto Off is turned on.  When Auto Off has activated, the LED Display will 
blink “OFF”. To disable the Auto-Off feature, enter “00”. If any key is pressed during the selected time 
out period, the Auto Off timer is reset. The system will return to normal operation. At the end of the 
time out period, the system will enter Auto Off. Power is turned off to the heater and the LED Display 
will show a flashing “OFF ” and the LED indicator will turn red.

 

Press and release the PROGRAM Key 

to move to the next step.

 

 
7.  Scan Enable / Disable 

Press and release the Scroll 

 

UP Key to enable or disable the scan mode feature. When enabled 

the scan feature of the MBT 350 scans each channel and display it’s information individually for 3 
seconds than continually repeats the order. Press and release the PROGRAM Key to move to the 
next step. 
 
 
 
 
 
 
 
 
 
 
 
 

©2005 PACE Inc., Annapolis Junction, Maryland All Rights Reserved                                                     Page 14 of 19 
 

 

Содержание 5050-0552



















Отзывы: