background image

Safety 

 

Safety Guidelines  

 

The following are safety precautions that personnel must understand and follow when using or 
servicing this product. 

 

1.   

POTENTIAL SHOCK HAZARD - 

Repair procedures on PACE products should be 

performed by Qualified Service Personnel only.  Line voltage parts may be exposed 
when the equipment is disassembled.  Service personnel must avoid contact with these 
parts when troubleshooting the product. 

2.   To prevent personnel injury, adhere to safety guidelines in accordance with OSHA and 

other applicable safety standards.  

3.   SensaTemp handpiece heaters and installed tips are hot when the handpiece is powered 

on and for a period of time after power off.  

DO NOT

 touch either the heater or the tip.  

Severe burns may result. 

4.   PACE Tip & Tool Stands and handpiece cubbies are designed specifically for use with 

the associated handpiece and houses it in a manner that protects the user from 
accidental burns.  Always store the handpiece in its holder.  Be sure to place the 
handpiece in its holder after use and allow for cooling before storing.  

5.   Always use PACE systems in a well ventilated area.  A fume extraction system such as 

those available from PACE are highly recommended to help protect personnel from 
solder flux fumes. 

6.  Exercise proper precautions when using chemicals (e.g., solder paste).  Refer to the Material 

Safety Data Sheet (MSDS) supplied with each chemical and adhere to all safety precautions 
recommended by the manufacturer. 

 

 

System Set-Up 

 
 Set up the ST 25 system using the following steps and associated drawings. 
 

1.  Store the shipping container in a convenient location.  Reuse of these 

containers will prevent damage if you store or ship your system. 

2.  Place the Power Switch in the “OFF” or “0” position.  

 

Mounting Options 

 

The ST 25 can be placed directly on a workbench or it also can also be mounted under a workbench 
or shelf to conserve space (

optional

 

mounting bracket sold separately

).  To mount the system in 

this way (ST 50 shown): 
 

1.  Mount the bracket in the desired location (fasteners not 

supplied). 

2.  Insert the 2 Mounting Screws (head first) into the power 

source mounting slots. 

3.  Place the washers over the screws. 
4.  Fit the power source between the bracket’s support arms 

and place the screws into the slots on the support arms. 

5.  Place the nut on the screw and tighten by hand. 
6.  Angle the power source so the operator can see the front 

panel easily. 

7.  Tighten the nuts with a wrench or pliers. 

 
 
 
 
 
 
 

w w w . e k t

2

. c o m

Содержание 5050-0530












Отзывы: