background image

 
TITLE                                                                                                                         PAGE 

 
General Information 

Introduction...........................................................................................................3 
Specifications .......................................................................................................3 
Parts Identification................................................................................................4 

Safety 

Safety Guidelines .................................................................................................5 

System Set-Up 

Mounting Options ....................................................................................................5 
Tip & Tool Stand ......................................................................................................6 
Handpiece Connection ............................................................................................6 

System Power Up ..........................................................................................................6 
Heater Burn In Procedure ..............................................................................................6 
Operation 

Variable Temperature Control ..............................................................................7 
Temperature Dial Lock .........................................................................................7 
LED Operation......................................................................................................7 

Temperature Dial Adjustment ........................................................................................8 
Corrective Maintenance 

Power Source .......................................................................................................8 
Handpieces...........................................................................................................9 

Packing List ....................................................................................................................9 
Spare Parts ....................................................................................................................9 
Service ..........................................................................................................................10 
PACE LIMITED WARRANTY STATEMENT.................................................................10 
Contact Information.......................................................................................................11 
 

 

 

 

w w w . e k t

2

. c o m

Содержание 5050-0530












Отзывы: