Pace 20A Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 27

Pace 20A Скачать руководство пользователя страница 13

11

Handpiece Connection

Connect the handpiece (or PS 50) connector plug into the Power Receptacle in the
following manner.

1. Turn the Locking Ring fully

counterclockwise with the Connector
Key end facing the power source.

2. Align the Connector Key with the

Receptacle Keyway.

3. Insert the connector into the power

receptacle.

4. Turn the Locking Ring fully clockwise

to secure in place.

Air Hose Routing

When using an Air Handpiece (e.g., SX-70
Sodr-X-Tractor) or a Tip-Evac Fume Extraction
System, any associated air hose(s) can be routed
through the 2 Air Hose Feed Thru holes located
on the bottom of the power source.

System Power Up

1. Insert the female end of the power cord into the AC Power Receptacle at

the rear panel of the power source.

2. Plug the prong end (male end) of the power cord into a 3 wire grounded

AC supply receptacle. The system is now ready for operation.

CAUTION

To insure operator safety, the AC supply receptacle must be checked for
proper grounding before initial operation.

3. Read the “Operation” section of this manual thoroughly before operating

the system. Included is a description of Sodr-Pen operation. Shipped
with ST 20A-TT and ST 20A-PS systems is an additional Operation &
Maintenance manual which details operation of the TT-65 ThermoTweez
handpiece or PS-50 Prep-Set.

Set-Up

«
...
11
12
13
14
15
...
»

Содержание 20A




























Отзывы:

Нет отзывов