background image

General Safety

  8

         CAUTION!
         ALL FUELS ARE FLAMMABLE

• Fire hazard - keep fuel away from all 
sources of ignition for example heaters, 
lamps, sparks from grinding or welding.

• DO NOT carry out hot work on tanks that 
have contained fuel.

• ALWAYS keep the work area tidy.

• ALWAYS clean up spills promptly using 
absorbent granules and a lidded bin.

• ALWAYS dispose of waste fuels correctly.

      General Fuel Safety

         CAUTION!
         ALL FUELS ARE FLAMMABLE

• ALWAYS fuel and de-fuel in a well ventilated 
area outside of buildings.

• ALWAYS wear correct, suitable and fit for 
purpose Personal Protective Equipment (PPE),  
suggested items are but not limited to safety 
gloves, overalls.

• When fueling/de-fueling ALWAYS avoid 
inhaling fumes.

• When de-fueling ALWAYS use a proper fuel 
retriever.

• ALWAYS carry fuel in the correct and clearly 
marked container.

      Fueling / De-Fueling

• Electricity can kill – NEVER work on 
LIVE/ENERGISED equipment.

• Prior to carrying out any maintenance work 
you MUST identify electrical isolation methods 
and isolate all electrical supplies.

• Prior to use and with all electrical supplies 
isolated, you MUST check all electrical cables, 
plugs and connectors for the following;

• Are intact and have no signs of damage, to 
include but not limited to bare wires, chaffing, 
cuts and loose wiring.

• If there are any signs of damage, the 
damaged item MUST be taken out of service 
until the damage has been repaired by an 
electrically competent person.

• All trailing cables should be routed so as not 
to cause any kind of trip hazard.

• NEVER work on or near electricity with wet 
hands, wet clothing and wet gloves.

      Electrical Safety (Where 
Applicable)

Batteries present a risk if they become 
damaged by the possible leaking of 
electrolyte. This electrolyte is an acid and can 
cause serious burn injuries. Care should be 
taken when working on or near them. 

NOTE 

the electrolyte may be in a liquid or gel form.

Should you come in to contact with electrolyte 
you should;

• Remove all clothing contaminated with 
electrolyte. If you cannot remove then saturate 
them in water.

• Get medical assistance as soon as possible.

Batteries (Where Present)

!

!

Содержание P5100SPE





















































Отзывы: