P.I.T. PSP400-C1, Руководство по эксплуатации

Страница: 9 / 22

Square Sander
8
as in case of damage resulting from improper
storage (corrosion of metal parts);
- natural wear and tear on the parts of the
electric machine, as a result of long-term op-
eration (determined on the basis of the signs
of full or partial depletion of the specified
mean life, great contamination, presence of
rust outside and inside the electric machine,
waste lubricant in the gearbox);
- use of the tool the purposes for other than
specifi ed in the operating instructions.
- mechanical damages to the tool;
- in the event of damages due to non-obser-
vance of the operating conditions specifi ed in
the instruction (see chapter “Safety Precau-
tions” of the Manual).
- damage to the product due to non-obser-
vance of the rules of storage and transporta-
tion.
Preventive maintenance of electric machines
(cleaning, washing, lubrication, replacement
of anthers, piston and sealing rings) during
the warranty period is a paid service.
The service life of the product is 3 years. Shelf
life is 2 years. It is not recommended for oper-
ation after 2 years of storage from the date of
manufacture, which is indicated in the serial
number on the label of the instrument, without
preliminary verifi cation (for the defi nition of the
date of manufacture, see the User’s Manual
earlier).
The owner is notified of any possible viola-
tions of the above terms of wa rranty service
upon completion of diagnostics in the service
center.
The owner of the tool entrusts the diagnostic
procedure to be conducted in the service cen-
ter in his absence.
Do not operate the electric machine when
there are signs of excessive heat, sparking, or
noise in the gearbox. To determine the cause
of the malfunction, the buyer should contact
the warranty service center.
Malfunctions caused by late replacement of
carbon brushes of the engine are eliminated
at the expense of the buyer.
5. The warranty does not cover:
- replacement accessories (accessories and
components), for example: batteries, discs,
blades, drill bits, borers, chucks, chains,
sprockets, collet clamps, guide rails, tension
and fastening elements, trimming device
heads, base of grinding and belt sander ma-
chines, hexagonal heads, etc.,
- fast wearing parts, for example: carbon
brushes, drive belts, seals, protective covers,
service. Without presenting this certifi cate, no
claims are accepted. In case of loss or dam-
age, the warranty certifi cate is not restored.
2. The warranty period for the electric ma-
chine is 12 months from the date of sale,
during the warranty period the service depart-
ment eliminates manufacturing defects and
replaces parts that have failed due to the fault
of the manufacturer free of charge. In the war-
ranty repair, an equivalent operable product
is not provided. Replaceable parts become
property of service providers.
P.I.T is not liable for any damage that may be
caused by operation of the electric machine.
3. Only clean tool accompanied with the
following duly executed documents: this War-
ranty Certifi cate, Warranty Card, with all fi elds
fi lled out, bearing the stamp of the trade orga-
nization and the signature of the buyer, shall
be accepted for warranty repair.
4. Warranty repair is not performed in the fol-
lowing cases:
- in the absence of a Warranty Certifi cate and
a Warranty Card or their incorrect execution;
- with failure of both a rotor and a stator of the
electric engine, charring or melting of primary
winding of the welding machine transformer,
charging or starting-charging device, with in-
ternal parts melting, burn down of electronic
circuit boards;
- if a Warranty Certifi cate or a Warranty Card
does not correspond to this electric machine
or to the form established by the supplier;
- upon expiration of the warranty period;
- at attempts of opening or repair of the elec-
tric machine outside the warranty workshop;
making constructive changes and lubrication
of the tool during the warranty period, as ev-
idenced, for example, by the creases on the
spline parts of the fasteners of non-rotational
parts.
- when using electric tools for production or
other purposes connected with making a prof-
it, as well as in case of malfunctions related
to instability of the power network parameters
exceeding the norms established by GOST;
- in the events of improper operation (use the
electric machine for other than intended pur-
poses, attachments to the electric machine of
attachments, accessories, etc. not provided
by the manufacturer);
- with mechanical damage to the case, pow-
er cord and in case of damages caused by
aggressive agents and high and low tempera-
tures, ingress of foreign objects in the ven-
tilation grids of the electric machine, as well