MAINTENANCE
DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
Power tools that are no longer usable should not be disposed of
with household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council authority
for recycling advice.
Recycling packaging reduces the need for landfill and raw materials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
local council authority for recycling advice.
Changing the Blade
1. Ensure the table saw plug is disconnected from the mains power supply.
2. Lower saw blade fully.
3.
Remove the side panel by first removing the 4 screws using a Phillips head
screwdriver
4.
Remove the 4 screws from the blade cover then remove the blade cover
from the saw.
5.
Using the 8mm spanner provided to hold the
spindle, undo the blade nut by turning anti-
clockwise direction with the 19mm spanner
6. Remove the nut and outer flange.
7. Carefully remove the blade from the shaft.
8. Clean out any dirt or sawdust.
9.
Fit the new blade onto the spindle taking care that the inner flange sits
behind the blade.
10. Refit outer flange and nut onto spindle
11
.
Using the 8mm spanner provided to hold the spindle, tighten the blade nut by
turning clockwise direction with the 19mm spanner
Note:
Make sure the saw blade turns freely by turning the blade by hand before
using the saw
11. Re
peat steps 3-4 above in reverse order for blade cover & side panel
assembly.
Switch
SPTSB1208-01
Inner Blade Flange
SPTSB1208-99
Blade Nut M12
SPTSB1208-96
Outer Blade Flange
SPTSB1208-97
Carbon Brush (Pair)
SPTSB1208-110
Blade
Ø
210mm x
Ø
25mm x 24T
SPTSB1208-98
BLADES:
You will find a selection of blades available from the
Tool Shop at Bunnings Warehouse.
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
WARNING!:
BEFORE CLEANING YOUR TABLE SAW OR
CARRYING OUT ANY MAINTENANCE PROCEDURE,
MAKE SURE THAT THE MOTOR IS OFF AND THE TOOL
DISCONNECTED FROM THE POWER SUPPLY TO PREVENT
ACCIDENTAL STARTING.
CAUTION!
NEVER TRY TO USE A BLADE THAT IS LARGER
THAN THE STATED CAPACITY OF THE TABLE SAW. IT MIGHT
COME INTO CONTACT WITH THE BLADE GUARDS AND RISK
PERSONAL INJURY OR DAMAGE TO THE TABLE SAW. THIS
WILL NOT BE COVERED UNDER WARRANTY.
CAUTION!
NEVER USE A BLADE THAT IS TOO THICK TO
ALLOW THE OUTER BLADE WASHER TO ENGAGE WITH
THE FLATS ON THE SPINDLE. IT WILL PREVENT THE BLADE
NUT FROM PROPERLY SECURING THE BLADE ONTO THE
SPINDLE.
CAUTION!
ENSURE THAT ANY SPACERS AND SPINDLE
RINGS THAT MAY BE REQUIRED SUIT THE SPINDLE AND
BLADE THAT ARE FITTED.
WARNING!:
TO ENSURE THE CORRECT BLADE ROTATION
ALWAYS INSTALL THE BLADE WITH THE BLADE TEETH
POINTING IN THE DIRECTION OF ROTATION. ENSURE THE
ARROW DIRECTION ON THE BLADE CORRESPONDS WITH
THE ARROW ON THE BLADE COVER.
Carbon Brushes
When the carbon brushes wear out, the table saw will
spark and/or stop. Discontinue use as soon as this
happens. They should be replaced prior to recommencing
use of the table saw. Carbon brushes are a wearing
component of the table saw therefore not covered under
warranty. Continuing to use the table saw when carbon
brushes need to be replaced may cause permanent
damage to the table saw. Carbon brushes will wear out
after many uses but when the carbon brushes need to be replaced, take the
table saw to an electrician or a qualified power tool repairer for a quick and low
cost replacement. Always replace both carbon brushes at the same time.
Note:
Ozito Industries will not be responsible for any damage or
injuries caused by the repair of the table saw by an unauthorised
person or by mishandling of the table saw.
Sparking visible through the housing air vents
A small amount of sparking may be visible through the housing vents. This is
normal and does not indicate a problem.
V
Volts
Hz
Hertz
~
Alternating current
W
Watts
/min
Revolutions or
reciprocation per minute
Double insulated
Regulator compliance mark
n
o
No load speed
Read instruction manual
Wear hearing protection
Wear eye protection
Wear breathing protection
Blade Nut
Inner Flange
Outer Flange
Blade
Spindle
