MAINTENANCE
DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
TROUBLESHOOTING
Power tools that are no longer usable should not be disposed of
with household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council authority
for recycling advice.
Recycling packaging reduces the need for landfill and raw materials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
local council authority for recycling advice.
The screwdriver is not operating
Ensure that the forward/reverse button is pushed to the left of the tool for forward
rotation or pushed to the right for reverse rotation.
The battery could be depleted and requires charging. Connect the charger and
allow the battery to charge before operating.
Bit cartridge is not rotating
The loading switch may not be pushed backwards completely. Ensure that the
loading switch is pushed back and then rotate the cartridge.
Loading switch will not move
The bit cartridge may not be aligned properly. Try rotating the cartridge into
another position and then back into the desired place.
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR YOUR BATTERY
CHARGER.
1.
Before using the charger read all instructions and cautionary markings on the charger, battery pack and
the product using the battery pack.
2.
This charger is not intended for any uses other than charging rechargeable batteries. Any other use may
result in risk of fire, electric shock or electrocution.
3.
Do not place any object on top of the charger or place the charger on a soft surface that may result in
excessive internal heat. Place the charger in a position away from any heat source.
4.
To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when discon-
necting the charger.
5.
Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise subjected to
damage or stress.
6.
An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could
result in the risk of fire, electric shock or electrocution.
7.
Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any
way. Have it checked by an electrician or power tool repairer.
8.
Do not disassemble charger. Take it to an electrician or power tool repairer when service or repair is
required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.
9.
To reduce risk of electric shock, unplug the charger from the outlet before attempting any cleaning.
Removing the battery pack will not reduce this risk.
10.
Never attempt to connect 2 chargers together.
11.
DO NOT store or use the tool and battery pack in locations where the temperature may reach or exceed 40ºC
(such as inside sheds or metal buildings in summer).
12.
The charger is designed to operate on standard household electrical power (240 volts). Do not attempt to
use it on any other voltage!
13.
The battery pack is not fully charged out of the carton. First read the safety instructions and then follow
the charging notes and procedures.
14.
The longest life and best performance can be obtained if the battery pack is charged when the air tem-
perature is between 18 - 24ºC. Do not charge the battery pack in an air temperature below 10ºC or above
40ºC. This is important and will prevent damage to the battery pack.
15.
Do not incinerate the battery pack even if it is seriously damaged or is completely worn out. The battery can
explode in a fire.
16.
Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or
cracks, immediately discontinue use and do not recharge.
17.
During charging, the battery must be placed in a well ventilated area.
BATTERY AND CHARGER SAFETY WARNINGS
1. When not in use, the screwdriver should be stored in a dry, frost
free location, keep out of children’s reach.
2. Keep ventilation slots of the screwdriver clean at all times.
3. If the housing of the screwdriver requires cleaning, do not use
solvents but cloth only.
4. Blow out the ventilation slots with compressed air periodically .
Note:
Ozito Industries will not be responsible for any damage or
injuries caused by repair of the screwdriver by an unauthorised
person or by mishandling of the tool.
Warning
Read instruction manual
mA Milliamperes
Polarity
Thermal cut-out protection
Transformer Energy
Rating (MEPS)
Double insulated
/min Revolutions or
reciprocation per minute
Ah
Amp hour
Indoor use only
Nm Newton Meters
n
o No load speed
V
Volts
Hz
Hertz
ac/~ Alternating current
W
Watts
Direct current
dc/
Wear eye protection
Wear ear protection
Regulator compliance mark
Diameter
mm
Millimetres
Recycle battery
Do not put in the rubbish
Do not incinerate Do not get battery wet
Lithium Ion battery
Do not use or store battery in
temperatures exceeding 50ºC
