![background image](http://html.mh-extra.com/html/ozito/rsh-2435/rsh-2435_instruction-manual_1666521006.webp)
6. BLADE REPLACEMENT
MAINTENANCE cont.
4. Place a screwdriver (not
supplied) though the slot in
the blade plate, this will secure
the rotating blade plate in its
position allowing you to remove
both blades. The screws may
be tight due to corrosion and
dirt buildup. Ensure that the
supplied hex key is a good fit
into the screw and that the hex key is held firmly and at right angles
to the blade plate.
Remove the 2 blade securing screws by rotating the hex key in the
anti-clockwise direction.
To remove the second blade repeat step 4.
5. If the opposite side of the blades are new, the blades can be
reversed to use the new side. If both sides of the blades are worn
then replace the blades and retighten the blades by following steps
4-5 in reverse. If new blades are being fitted ensure that the new
blade securing screws are fitted at the same time. Ensure all blade
securing screws are tight prior to operation.
Note:
It is recommended to add Loctite
®
222 Threadlocker to the thread
of the blade securing screw, Loctite
®
222 Threadlocker is available from
all Bunnings stores. This assists in securing the screw and reduces the
chance of the blade securing screw vibrating loose whilst in operation.
6. Once the blades are removed/
reversed, lower the housing and
tighten the locking knob by rotating
in a clockwise direction. Ensure it is
securely fitted to the housing.
General maintenance
The shredder requires very little maintenance. In order to maintain the
efficiency of the machine and achieve a long service life observe the
following:
•
Keep the air openings clean and free of obstructing material.
•
Periodically check that all nuts and screws are secure.
•
Spray the rolling cutter head after each use with a spray lubricant to
protect against corrosion.
•
Always clean the shredder after each use. Brush away dirt and plant
residue which may be caught in the roller cutter. Wipe clean the
outside of the shredder with a cloth which has been moistened with a
mild detergent and water.
•
Store the shredder upright in a dry place.
Note:
Ozito Industries will not be responsible for any damage or injuries
caused by the repair of the tool by an unauthorised person or by
mishandling of the tool.
WARNING!
ENSURE THE BLADE SECURING
SCREWS SECURING THE BLADES ARE FULLY
TIGHTENED PRIOR TO OPERATION. IF THERE IS ANY
VIBRATION OR ABNORMAL NOISE AFTER RE-STARTING
THE SHREDDER, IMMEDIATELY STOP OPERATION.
DISCONNECT FROM THE MAINS POWER AND CHECK
THAT THE BLADES ARE ASSEMBLED CORRECTLY AND
SECURELY TIGHTENED.
Replacing blades
The blades supplied with the shredder are reversible. The blades
can also be re-sharpened if they become blunt over a period of time.
Additional blades & bolts can be obtained as spare parts. Always
reverse or replace both blades at the same time.
To remove the blades proceed as follows:
1. Ensure the shredder is turned off
and disconnect from the mains
power. Unscrew the locking knob
in an anti-clockwise direction. The
thread on the locking knob is quite
long, the operation will require
approximately 15 rotations to fully
open the housing.
2. After unscrewing the locking knob lift
the housing upwards to gain access
to the cutting blades.
3. There are two blades and
these are each fixed to the
rotating blades plate with two
hex head screws. To remove
the blades first clean out any
debris and build up of material
from the blades. Then undo
the 8 screws and remove the
cover plate.
CAUTION!
BLADES ARE SHARP, HANDLE WITH CARE,
IT IS RECOMMENDED TO USE GARDENING OR SAFETY
GLOVES WHEN HANDLING THE BLADES.
WARNING!:
ALWAYS DISCONNECT THE
SHREDDER FROM THE POWER SUPPLY
BEFORE PERFORMING ANY MAINTENANCE.