manualshive.com logo in svg

Ozito Power X Change PXTSS-018, Инструкция по эксплуатации, Страница: 5 / 6

Поделиться
Скачать
Ozito Power X Change PXTSS-018 Скачать руководство пользователя страница 5

MAINTENANCE

DESCRIPTION OF SYMBOLS

Wear eye, ear & breathing 

protection

Warning

Regulatory Compliance Mark

(RCM)

mm

V

n

0

/min

Volts

Millimetres

No load speed

Revolutions or reciprocations 

per minute

Read Instruction Manual

Power tools that are no longer usable should not be disposed 

of with household waste but in an environmentally friendly 

way. Please recycle where facilities exist. Check with your local 

council authority for recycling advice.

Recycling packaging reduces the need for landfill and raw 

materials. Reuse of recycled material decreases pollution in the 

environment. Please recycle packaging where facilities exist. 

Check with your local council authority for recycling advice.

CARING FOR THE ENVIRONMENT

SPARE PARTS

Spare parts can be ordered from the Special Orders 

Desk at your local Bunnings Warehouse. 
For further information, or any parts not listed here, 
visit www.ozito.com.au or contact Ozito Customer 
Service: 
Australia 1800 069 486 
New Zealand 0508 069 486 
E-mail: [email protected]

WARNING! 

BEFORE CLEANING OR CARRYING OUT 

ANY MAINTENANCE PROCEDURE, ENSURE THAT 
THE BATTERY HAS BEEN REMOVED.

Cleaning

•  Keep the ventilation slots of the tool clean at all times to ensure efficient 

operation.

•  After each use, blow air through the tool housing to ensure it is free from 

all dust, dirt, etc. Build up of dust or dirt particles may cause the tool to 

overheat and shorten the life of the tool.

•  If the housing of the tool requires cleaning, do not use solvents. Use of a 

cloth only is recommended. 

•  Never allow any liquid to get inside the tool, never immerse any part of 

the tool into liquid.

Replacing The Hook & Loop Sanding Pad

After considerable use, the hook and loop backing pad surface will become 

worn, and must be replaced when it no longer offers a firm grip. Contact 

Ozito Customer Service for replacement parts.

1.  To replace, remove the ten Philips 

head screws on the base of the 

unit.

2.  Place the new backing pad on the 

tool and replace the screws to 

secure it.

Storage

When not in use, the tool should be stored in a dry, frost free location, keep 

out of children’s reach.

Note: 

Ozito Industries will not be responsible for any damage or  

injuries caused by repair of the tool by an unauthorised person or by 

mishandling.

Содержание Power X Change PXTSS-018







Отзывы:

Нет отзывов