manualshive.com logo in svg

Ozito Power X Change PXTSS-018, Инструкция по эксплуатации, Страница: 4 / 6

Поделиться
Скачать
Ozito Power X Change PXTSS-018 Скачать руководство пользователя страница 4

Fitting The Battery Pack

1.  Slide the battery into the battery 

seating until it clicks into place.

2.  To remove the battery, hold down 

the battery release button and 

slide the battery out.

Starting & Stopping The Sander

1.  Press the on/off switch towards the ‘I’ position 

to start the sander.

2.  Press the on/off switch towards 

the ‘0’ position to switch the 

unit off.

Sanding Procedure

1.  Secure the material to be sanded.

2.  Firmly grasp the sander and turn 

the unit on.

3.  Let the motor build up to 

maximum speed. Gradually lower 

it onto the workpiece with a 

slight forward movement.

4.  For optimum results, move the 

sander back and forth in steady 

strokes.

Note:

 Keep the entire sanding 

pad in contact with the workpiece 

at all times during sanding.

5.  Upon completion of the sanding operation, remove the sander from the 

workpiece and then turn off the sander.

Sanding Tips

Never force the sander. The weight of the sander supplies adequate 

pressure, allowing the sandpaper to do the work. Applying additional 

pressure will slow the motor, rapidly wear the sandpaper, and greatly 

reduce the sander speed. This will slow the removal rate and produce an 

inferior quality surface.

Note:

 Excessive pressure will overload the motor, causing possible 

damage to the sander by overheating the motor; or damage to the 

workpiece.

Be sure to check your workpiece often. The sander is capable of removing 

material rapidly, especially with coarse paper.

The orbital action of your sander allows you to sand with the grain, or at 

any angle across it for most sanding jobs. In the final stages a better finish 

will be achieved by sanding with the grain.

Do not sand on one spot for too long. The sander’s rapid action may remove 

too much material, creating an uneven surface.

3. STARTING THE SANDER

4. USING THE SANDER

OPERATION

PXTSS-018

WARNING! 

THIS PRODUCT IS NOT

RECOMMENDED FOR SANDING DRYWALL OR
PLASTER DUE TO THE ULTRA-FINE SANDING
PARTICLES PRODUCED. DRYWALL SANDERS IN
CONJUNCTION WITH DUST EXTRACTION ARE
RECOMMENDED FOR DRYWALL AND PLASTER
SANDING APPLICATIONS.

Содержание Power X Change PXTSS-018







Отзывы:

Нет отзывов