background image

ONLINE MANUAL

Scan this QR Code with your 

mobile device to take you to 

the online manual.

Installing The Battery Pack

1.  Slide the battery into the tool 

base until it clicks into place.

Removing The Battery Pack

1.  Hold down the battery release 

button.

2.  Slide the battery out.

Covering The Battery

A Splash Proof Battery Cover has been provided with this unit to prevent 

paint splatters from marking up your battery. 

1.  Slide the Battery Cover over the 

attached battery.

2.  Pull the drawstring taut to secure 

it.

1. 1L Paint Pot
2. Spray Pattern Adjustor
3. Spray Width Deflector
4. Detachable Spray Head
5. Spray Head Locking Knob

6. Spray Gun
7. Battery Seating
8. Flow Regulator Dial
9. On/Off Trigger
10. Suction Tube

11. Ø1.5mm Nozzle
12. Ø1.8mm Nozzle
13. Ø2.2mm Nozzle
14. Spare Deflector Ring

15. Splash Proof Battery Cover
16. Viscosity Measuring Cup
17. Cleaning Brush
18. Cleaning Needle

This tool is compatible with all batteries & chargers from the Ozito Power X Change 
range.

CORDLESS OUTDOOR SPRAY GUN

ACCESSORIES

BATTERY & CHARGER

KNOW YOUR PRODUCT

1. FITTING THE BATTERY

SETUP & PREPARATION

2

1

3

5

6

4

18

7

10

9

8

17

11

12

13

14

16

15

WARNING! 

ENSURE THE BATTERY COVER IS USED 

WITH THE PAINT SPRAYER AT ALL TIMES.

Содержание Power X Change PXOSGS-018









Отзывы: