MAINTENANCE
DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
TROUBLE SHOOTING
Power tools that are no longer usable should not be disposed of
with household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council authority
for recycling advice.
Recycling packaging reduces the need for landfill and raw materials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
local council authority for recycling advice.
• Keep the vents of the saw clean at all times. If possible, prevent foreign matter
from entering the vents.
• After each use, blow air through the saw housing and guard, to ensure it is
free from all dust particles which may build up. Build up of dust particles may
cause the saw to overheat and fail.
• If the enclosure of the saw requires cleaning, do not use solvents but a moist
soft cloth only. Never let any liquid get inside the saw; never immerse any part
of the saw into a liquid.
Carbon Brushes
When the carbon brushes wear out, the saw will
spark and/or stop. Discontinue use as soon as
this happens. They should be replaced prior to
recommencing use of the saw. Carbon brushes are a
wearing component of the saw therefore not covered
under warranty. Continuing to use the saw when
carbon brushes need to be replaced may cause
permanent damage to the saw. Carbon brushes
will wear out after many uses. When the carbon brushes need to be replaced,
take the saw to an electrician or a power tool repairer for a quick and low cost
replacement. Always replace both carbon brushes at the same time.
Note: Ozito Industries will not be responsible for any damage or injuries
caused by the repair of the saw by an unauthorised person or by mishandling
of the saw.
Circular Saw Tips
Always hold the soft grip handle with one hand and the front handle with the other.
Maintain a firm grip and operate the on/off switch with a positive action.
Never force the saw. Use light and continuous pressure.
When cutting is interrupted, to resume cutting, depress the lock-off button and
squeeze the on/off switch and allow the blade to reach full speed, re-enter the cut
slowly and resume cutting.
When cutting across the grain, the fibres of the wood have a tendency to tear and
lift. Advancing the saw slowly minimizes this effect. For a finished cut, a cross cut
blade or mitre blade is recommended.
Sparking visible through the housing air vents
A small amount of sparking may be visible through the housing vents.
This is normal and does not indicate a problem.
Excessive sparking visible through the housing air vents
and/or the saw failing to operate
May indicate the carbon brushes have worn out and need to be
replaced. Carbon brushes should only be replaced by a qualified
electrician or power tool repairer.
WARNING:
THE SAW IS RECOMMENDED FOR WOOD
CUTTING ONLY AND IS NOT INTENDED TO BE USED
WITH ABRASIVE OR MASONRY/WET DIAMOND WHEELS.
USING WATER OR OTHER LIQUID COOLANTS WITH THIS
MACHINE MAY RESULT IN SHOCK OR ELECTROCUTION.
WARNING:
AFTER COMPLETING A CUT AND THE ON/OFF
SWITCH IS RELEASED, BE AWARE OF THE TIME IT TAKES
FOR THE BLADE TO COME TO A COMPLETE STOP. HOLD
THE SAW AWAY FROM YOUR BODY UNTIL THE BLADE
STOPS COMPLETELY. THIS MAY HELP TO PREVENT
SERIOUS INJURY.
WARNING:
AVOID ACCIDENTAL STARTING BY
DISCONNECTING THE TOOL FROM THE POWER SOURCE
BEFORE ASSEMBLING OR MAKING ANY ADJUSTMENTS.
Blade Bolt
SPCSW7000-01
Outer Flange
SPCSW7000-03
Inner Flange
SPCSW7000-05
Carbon Brush (Pair)
SPCSW7000-44
Brush Holder (Pair)
SPCSW7000-45
Switch
SPCSW7000-51
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
V
Volts
Hz
Hertz
~
Alternating current
W
Watts
/min
Revolutions or
reciprocation per minute
Double insulated
Regulator compliance mark
n
o
No load speed
Warning
