Ozito 43.405.42, Оригинальная инструкция по эксплуатации

Страница: 21 / 32

GB
- 21 -
6.8 Putting away loose parts (Fig. 15)
•
When not in use, the parallel stop (7) and
stop rail (23) can both be secured as shown
in Fig. 15a.
•
The cross stop (14), push stick (3) and the
two wrenches (38+39) can be secured as
shown in Fig. 15b.
6.9 Connection for dust extractor (Fig. 2, 9,
26)
A connection for a dust extractor is provided on
the extractor adapter on the housing (16) and on
the saw blade guard (2).
6.9.1 Dust extraction using a wet & dry vac
(Fig. 2, 9)
•
A wet & dry vac is not supplied with the pro-
duct and is available as an accessory.
•
Attach the suction hose (10) to the machine
as described in 6.3.
•
Connect the wet & dry vac to the extractor
adapter on the housing (16).
6.9.2 Dust extraction using a vacuum ext-
raction system and extractor adapter set
(Fig. 9, 26)
•
The product is not supplied with an extractor
adapter set or a vacuum extraction system,
which are available as accessories.
•
Attach the suction hose (10) to the machine
as described in 6.3.
•
Attach the adapter (c) of the adapter set to
the extractor adapter on the housing (16).
•
A vacuum extraction system can now be
connected to the 100 mm diameter of the
adapter (c).
7. Using the saw
7.1. ON/OFF switch (Fig. 1, 16 / Item 11)
•
To turn the saw on, press the green button
„I“. Wait for the blade to reach its maximum
speed of rotation before commencing with
the cut.
•
To turn the equipment off again, press the red
button „0“.
7.2. Cutting depth (Fig. 1, 16)
Turn the hand wheel (8) to set the blade (4) to the
required cutting depth.
Turn anti-clockwise:
smaller cutting depth
Turn clockwise:
larger cutting depth
7.3 Parallel stop
The parallel stop (7) has to be used when making
longitudinal cuts in wooden workpieces.
7.3.1 Stop height (Fig. 18, 19)
•
The parallel stop (7) supplied with the bench-
type circular saw has two different guide
faces.
•
For thin material you must use the stop rail
(23) as shown in Fig. 19a, for thick material
you must use the stop rail as shown in Fig.
19b.
•
To change over the stop rail (23) to the lo-
wer guide face you have to slacken the two
knurled screws (26).
•
Remove the two screws (32) from the parallel
stop through the one slot (25) in the stop rail
(23).
•
Thread the two screws (32) into the other slot
(27) in the stop rail (23) and slide the stop rail
(23) back onto the parallel stop.
•
Retighten the two knurled screws (26) in or-
der to fix the stop rail (23).
•
The procedure for changing over to the high
guide face is the same.
•
Warning! When in use, the stop rail (23) must
always be screwed to the side of the parallel
stop (7) which faces the saw blade.
7.3.2. Cutting width (Fig. 17)
•
The parallel stop (7) can be mounted on eit-
her side of the saw table (1).
•
The parallel stop (7) has to be mounted in the
guide rail (28) of the saw table (1).
•
The parallel stop (7) can be set to the requi-
red dimension with the help of the scale (22)
on the guide rail (28).
•
You can clamp the parallel stop in the requi-
red position by pressing the eccentric lever
(12).
Anl_TSF_1211U_SPK7.indb 21 Anl_TSF_1211U_SPK7.indb 21 05.11.2019 14:37:50 05.11.2019 14:37:50