OXTS RT Series Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 133

background image

44

Oxford Technical Solutions

Wheel speed input

The wheel speed 1A input (J5-3) accepts TTL pulses from an encoder on a single wheel.
An encoder from a gearbox should not be used, and simulated TTL pulses (e.g. converted
from the CAN bus) should not be used either. The timing of the wheel speed input pulses
is critical and nothing should cause any delay to them.

The RT also accepts signals from quadrature wheel speed sensors. When using quadrature
sensors, connect one channel from the quadrature sensor to wheel speed 1A, and the other
to wheel speed 1B input (J5-5). The odometer input should be configured as per a normal
wheel speed sensor – the RT will automatically detect the use of the quadrature sensor.

The wheel speed input requires less than 0.8 V for a low pulse and more than 2.4 V for a
high pulse. Limited protection is provided on this port, however the input voltage should
not exceed 12 V.

Wheel speed input signal characteristics:

• 0 V to 12 V
• low < 0.8 V
• high > 2.4 V

The wheel that is used should not steer the vehicle. The RT will assume the wheel travels
straight.

IMU sync output pulse

The synchronising edge of the PPS is configurable in NAVconfig.

«
...
42
43
44
45
46
...
»

Содержание RT Series






































































































































Отзывы:

Нет отзывов

Похожие инструкции для RT Series

BML SL1-ALZ-ZZ Series

Бренд: Balluff Страницы: 26

Бренд: Hardy Barth Страницы: 27

Бренд: LATNEX Страницы: 55

Бренд: Laser Technology Страницы: 11

Бренд: Laser Technology Страницы: 62

Бренд: Raycus Страницы: 40

Бренд: RaycoWylie Страницы: 31

Бренд: ColorLite Страницы: 68

Бренд: Dwyer Instruments Страницы: 189

Бренд: Lowrey Страницы: 109

SoundTrack LxT N/Forcer

Бренд: Larson Davis Страницы: 12

Бренд: Mark-10 Страницы: 26

Бренд: janitza Страницы: 128

Бренд: SKF Страницы: 12

Бренд: NCS Страницы: 7

Бренд: Ferret Страницы: 18

Бренд: FASAR ELETTRONICA Страницы: 2

Бренд: Teledyne Страницы: 81

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды