Oxford Instruments Andor Apogee Aspen Series Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 45

Oxford Instruments Andor Apogee Aspen Series Скачать руководство пользователя страница 2

Version 1.4 rev 23 Oct 2017

Aspen

2

TABLE OF CONTENTS

SECTION 1: INTRODUCTION ........................................................................................ 6

1.1 TECHNICAL SUPPORT ....................................................................................... 6

1.2 DISCLAIMER ....................................................................................................... 7

1.3 COPYRIGHT AND PROTECTIVE NOTICES ....................................................... 7

1.4 TRADEMARKS AND PATENT INFORMATION ................................................... 7

1.5 ABOUT ANDOR APOGEE CAMERAS ................................................................ 7

1.6 REVISION HISTORY ............................................................................................ 7

1.7 SUPPLIED COMPONENTS ................................................................................. 8

............................................................................ 8

........................................................................................... 8

SECTION 2: PRODUCT OVERVIEW .............................................................................. 9

2.1 INTRODUCING THE ANDOR APOGEE ASPEN ................................................. 9

2.2 DESCRIPTION OF EXTERNAL FEATURES ...................................................... 10

................................................................ 11

SECTION 3: INSTALLING YOUR ASPEN CAMERA SOFTWARE ............................... 13

3.1 INSTALL/UPDATE APOGEE CAMERA DRIVER ............................................... 13

................... 13

3.2 INSTALL THE CAMERA CONTROL SOFTWARE ............................................. 14

dl ..................................................................................... 14

3.3 UNINSTALLING APOGEE SOFTWARE ............................................................. 14

3.4 USING YOUR ASPEN CAMERA ON A NETWORK .......................................... 15

................................ 15

«
1
2
3
4
...
»

Содержание Andor Apogee Aspen Series














































Отзывы:

Нет отзывов