Oxford Instruments Andor Apogee Aspen Series Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 45

Oxford Instruments Andor Apogee Aspen Series Скачать руководство пользователя страница 40

Version 1.4 rev 23 Oct 2017

Aspen

40

7. Carefully install the filters into openings of carousel. Only touch the filters at the outer edges and never touch

the center of a filter. When holding filters always use some kind of protection such as gloves or the glass
packing material. It is ok to rotate the carousel by hand to make it easier to install filters. Some filters will be
tighter than others when resting in the carousel openings, do not force into place. Center filters in carousel
openings (use four tooth picks around the edges of each filter if needed).

8. Fasten the filters using the screw and nylon washer combinations described on the next page.

Install filters using the below screws and nylon washers provided using the 1/16” Allen wrench provided. DO NOT OVER
TIGHTEN; this may physically distort your filters which will optically distort your image. Make sure filters do not move
after tightening. Rotate the carousel by hand to verify clearance under the circuit board.

«
...
38
39
40
41
42
...
»

Содержание Andor Apogee Aspen Series














































Отзывы:

Нет отзывов