Owon MSO7102T Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 117

background image

User’s Manual of

OWON

Color Mixed Signal Digital Storage Oscilloscope

Setting

Description

CH1-CH2

Subtract the Channel 2 wave form from the Channel 1
wave form.

CH2-CH1

Subtract the Channel 1 wave form from the Channel 2
wave form.

CH1+CH2

Add the Channel 1 wave form to the Channel 2.

Application of VERTICAL POSITION and VOLTS/DIV
Knobs

1.

The .

VERTIVAL POSITION

knob is used to adjust the vertical positions of the

wave forms of all Channels (including those resulted from the mathematical
operation).
The analytic resolution of this control knob changes with the vertical division.

2.

The

VOLTS/DIV

knob is used to regulate the vertical resolution of the wave

forms of all channels (including those obtained from the mathematical
manipulation), which can determine the sensitivity of the vertical division with

the sequence of 1-2-5. The vertical sensitivity goes up when the knob is rotated
clockwise and goes down when the knob is rotated anticlockwise.

3.

When the vertical position of the channel wave form is adjusted, the screen shows
the information concerning the vertical position at the lower left corner (see
Fig.27).

39

«
...
37
38
39
40
41
...
»

Содержание MSO7102T






















































































































Отзывы:

Нет отзывов

Похожие инструкции для MSO7102T

Бренд: OMCA Страницы: 72

Бренд: Barko Hydraulics Страницы: 92

Бренд: 3M Страницы: 2

Бренд: NAD Страницы: 10

Бренд: Ace Страницы: 17

Бренд: ACE INSTRUMENTS Страницы: 33

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: TapFlo Страницы: 35

Бренд: DANA Страницы: 8

Бренд: 2E Страницы: 6

Бренд: RASHA PROFESSIONAL Страницы: 11

Бренд: MADRIX Страницы: 24

Бренд: MADRIX Страницы: 28

Бренд: olympia electronics Страницы: 4

Бренд: Abus Страницы: 12

FLEX-FOOT ASSURE

Бренд: Össur Страницы: 82

Бренд: Össur Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды