Owon MSO5022 Скачать руководство пользователя страница 83

Страница: 83 / 107

User’s Manual of

OWON

Color Mixed Signal Digital Storage Oscilloscope

5. Press

“

”

till memory SEL as

“

setups

”

6. Press

“

”

till memory ID. display as

“

setups 0

”

7. Press

“

”

to save current various settings. Info window show

“

setting

saved successfully

”

8. Press

“

”

to recall the memory waveform or settings (refer to Fig. 82)

Fig 82

：

Waveform saving

How to use USB Mass storage device to storage



USB Mass storage device is to storage acquired data. Connect USB device into
the unit slot and press

“

”

, then the acquired data will save to the USB device.

And the waveform storage in USB device can be analyzed in computer with MSO
waveform analyzes software.

How to search

Searches have different operation according to different targets. Search target

including trigger position, BUS value, and pattern.
1

、

Search triggers position as following steps

、

Press

“

2(SEARCH)

”

and menu appears.

、

Press

“

”

till target display as

“

Trig position

”

、

Press

“

”

to start searching and current cursor will stop in the trigger

position

Содержание MSO5022












































































































Результаты поиска

Содержание MSO5022

Отзывы:

Бренды по названию

Популярные бренды

Owon MSO5022, Руководство пользователя

Результаты поиска

Содержание MSO5022

Отзывы:

Бренды по названию

Популярные бренды