OWL Fiber OWL 7+ Скачать руководство пользователя страница 48

Страница: 48 / 89

TEST PROCEDURES

LINK WIZARD

After a few seconds, the SOURCE REFERENCE POWER will be shown. Press

to continue.

DONE

Once the WaveSource Pro is set to AUTO mode, press

on the Fiber OWL 7+ to

set the SOURCE REFERENCE POWER.

TEST

Optical Source

WaveSource Pro

AUTO

PORT

MOD

Optical Source

WaveSource Pro

AUTO

PORT

MOD

Wavelength

Set source to AUTO or 1310nm

You will need to set a source
power reference for each
wavelength that you are testing.

Press TEST to measure.
Press DONE after testing all
wavelengths.

Testing...

Power

Typical

TEST

WAVE

BACK

DONE

SOURCE REFERENCE POWER

HELP

Wavelength

1310nm

1550nm

Set source to AUTO or 1310nm

You will need to set a source
power reference for each
wavelength that you are testing.

Press TEST to measure.
Press DONE after testing all
wavelengths.

TEST

WAVE

BACK

DONE

SOURCE REFERENCE POWER

HELP

Power

-10.20dBm

-10.04dBm

Typical

-10.00dBm

Note about Typical power values:

If the reference power levels are over 1 dB below
the typical value for that fiber type, the patch
cable either needs to be cleaned or replaced.

STEP 4: SETTING THE REFERENCE, cont.

Содержание Fiber OWL 7+


























































































Результаты поиска

Содержание Fiber OWL 7+

Отзывы:

Похожие инструкции для Fiber OWL 7+

Бренды по названию

Популярные бренды

OWL Fiber OWL 7+, Руководство по эксплуатации

Результаты поиска

Содержание Fiber OWL 7+

Отзывы:

Похожие инструкции для Fiber OWL 7+

Бренды по названию

Популярные бренды