background image

 

10.

 

Pull down on the bottom of the doors and mark the locations for the snaps. The front of 
the door goes inside the foot well as shown in fig. G. Screw the snaps into the plastic 
where previously marked and snap the doors on. If using a drill/driver to install snap 
studs, work slowly and use a lighter clutch setting so as to not overtighten and strip out 
the hole.  

 

Fig. G

 

 

11.

 

To open and stow the doors, move the zipper fully rearward and fold the bottom portion 
of the doors up.  Then begin to form a vertical roll with the door by rolling it inward from 
the front edge toward the rear of the door.   Secure in place using the two hook and loop 
straps provided.  Try to form a roll approximately 2” in diameter to assure that the door 
will not stick out very far while stowed. 

 
Cleaning and Storage Recommendations: 

1.

 

Before removing the enclosure for storage, make sure it is clean and dry, to prevent 
soiling the textile and scratching the clear vinyl windows. Clean with a soft rag or 
sponge using a mild liquid detergent soap and warm water solution. Let the enclosure 
dry thoroughly before attempting to roll for storage.  

 

2.

 

It is important that the enclosure be rolled up for storage rather than folding.  Folding 
will cause undesirable creasing of both the enclosure textile and the clear vinyl windows. 
Carefully roll up the enclosure similar to the way it was when it was packed at the 
factory. Put the rolled enclosure back into the carton for storage at a normal room 
temperature. It is best not to expose the enclosure to either extreme hot or cold 
temperatures when storing. 

 

3.

 

A special cleaner/conditioner is available from Over Armour that will greatly increase the 
service life of the cab enclosure. If needed, additional hook and loop sets are available, as 
well as other spare parts and hardware. Contact Over Armour for information.  

 

4.

 

Transporting or trailering your UTV with the enclosure installed is not generally 
recommended. It is best to remove the enclosure before transporting your UTV. 

Thank you for your purchase!

 

Snaps are facing 

inside

 the vehicle in 

this location 

Snaps are facing 

outside

 the vehicle in 

this location 

Содержание KAW-TERYX-FC01








Отзывы: