manualshive.com logo in svg

Outdoor living today 9x6 Cabana, Инструкция по сборке

Поделиться
Скачать
Outdoor living today 9x6 Cabana Скачать руководство пользователя страница 7

10.

Starting at Rear Corner, position a

Solid Wall Panel on top of plywood floor.
Depending on your preference, you may use
a solid or window wall panel in this position.
If using a solid wall, make sure panel is 
facing up.  

Important -

Make sure all walls are aligned in their
upright position. If not ,water may leak into
your shed. Unsure if panel is facing up or
down?  Check siding on window wall
panel to match alignment.

11.

The front and rear wall panels will sit flush at the

end of the plywood floor with the side panels 
sandwiching between them. 

Note:

Siding will overhang the floor by approx. 1/2” but

2x3 wall frame will sit flush on plywood floor.

1st Rear Wall Panel

1st Rear
Wall Panel

side of shed

Front

Side

2x3

wall

frame

Wall Plate

9. 

Starting with 

Solid Wall Panels

, carefully lay panel face down. Position and attach 

Wall Plate

to bottom of wall studs of each wall panel with 6 - 2 1/2” screws. Position so plates are flush with
framing.

Flush with Floor Framing

1-888-658-1658                        www.outdoorlivingtoday.com            [email protected]

Page 7

Содержание 9x6 Cabana



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды