Outdoor living today 8x8 Sunshed Garden Shed Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 29

background image

27.

When properly positioned, attach by screwing down into top wall framing with 4 -2” screws.

Top Plates should be flush
with inside of wall framing.

22 1/2 degree angle
cut end follows
angle of wall.

28.

Next, attach the

Side Top Plate

with a 33 3/4 degree cut down edge to high wall side. Once again,

position top plate on wall plate so it is flush with inside of wall plate. Side plate should also be flush with
Rear Top Plate. Secure with 4 - 2” screws per piece.

29.

Position remaining

Front Top Plate

and Side Top Plate (for short wall side) into position on wall

framing and secure with 4 - 2” screws per piece. Side Top Plate has a 22 1/2 degree cut down 1 edge.

Front Top Plate

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 11

«
...
9
10
11
12
13
...
»

Содержание 8x8 Sunshed Garden Shed






























Отзывы:

Нет отзывов

Похожие инструкции для 8x8 Sunshed Garden Shed

Edison Workbench

Бренд: WATSON Страницы: 19

Connect Space E0337

Бренд: Ideal-Standard Страницы: 2

Бренд: Forte Страницы: 35

Бренд: Profile Страницы: 5

Бренд: Whalen Страницы: 12

Бренд: East West Furniture Страницы: 4

BENNETT MS18-D1-1007-13

Бренд: Mainstays Страницы: 22

Бренд: Gami Страницы: 20

Бренд: Glacier bay Страницы: 4

Бренд: KAWOTI Страницы: 4

Бренд: IKEA Страницы: 2

Galleria Series CGSH

Бренд: RSA Lighting Страницы: 1

Бренд: italor Страницы: 5

Бренд: Homestar Страницы: 16

BEDFORD RECTANGULAR NIGHT STAND END TABLE...

Бренд: East West Furniture Страницы: 3

Бренд: Factory Furniture Страницы: 4

Bolitzo 930/8583

Бренд: Argos Страницы: 6

Shaper 643 Series

Бренд: Cooper Lighting Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды