Outdoor living today 8x12 SunShed Скачать руководство пользователя | Manualshive

Страница: 20 / 34

background image

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 20

51.

Complete installation for remaining Gussets

52.

Attach

Simpson Strong Ties

to Top Wall

framing and plates and also to the underside of the
rafters. Use 4 - 1 1/4” screws to secure. There are
14 Ties to complete. Long Roof Side Ties are
angled at 22 1/2 degrees (long side to walls).

53.

Position 3/4” x 3/4” x 41.5” long

Lexan Support Cleats

on each Long Rafter flush to end and

recessed 1/4” down from top of rafter. Nail to rafter using 6 - finishing nails.

Note,

Start nails in Supports

on ground first. Complete remaining 11 Lexan Support Cleats.

1/4” gap

54.

Identify all

Roof Panels.

There are 2 Outside Right, 2 Center and 2 Outside Left Roof Panels. The

outside of the panels will have shingles overhanging the battens. Starting with an Outside Roof Panel on
Short Roof Side, lift up and place a roof panel on rafters so centered on mid rafter. Lowest batten on roof
should be flush with end of rafter at bottom.

Battens flush
with shingles

D. Roof Section

Roof Batten flush
with rafter end.

Shingles overhang
battens to outside

Further secure Cleats with 2 - 1 1/4” screws.

Important

- Drill pilot holes to prevent splitting!

«
...
18
19
20
21
22
...
»

Содержание 8x12 SunShed



































Отзывы:

Нет отзывов

Похожие инструкции для 8x12 SunShed

Бренд: Palmako Страницы: 29

Бренд: new garden Страницы: 54

Sandy 5.0 FRF34-4432

Бренд: Palmako Страницы: 36

Бренд: Solid Страницы: 21

Бренд: Solid Страницы: 34

Бренд: Outdoor Life Products Страницы: 30

Бренд: Outdoor Life Products Страницы: 28

41212MR-12 SAND

Бренд: Gazebo penguin Страницы: 31

Бренд: Palmako Страницы: 54

Бренд: Palmako Страницы: 56

Бренд: Palmako Страницы: 63

Бренд: Palmako Страницы: 70

Бренд: Palmako Страницы: 60

Бренд: Palmako Страницы: 19

Бренд: Palmako Страницы: 104

FRAB19-4023FSC / 1059487

Бренд: new garden Страницы: 65

Бренд: Palmako Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды