Step 3: Attach Side Bars to the Legs
Step 4: Attach Wheels and Casters to the Legs
Locate:
• (2) Leg Support Brackets
• (8) 1/4-20 x .59 Bolts
Procedure:
Align the four holes in each side bar with the
holes near the top of each leg assembly. Insert
a 1/4-20 x .59 Bolt through each hole in the side
bar, then through the corresponding hole in the
leg assembly. Leave the screws loose for now.
Locate:
• (2) Casters
• (2) Wheels
• (2) Wheel Axle Pins
• (2) Axle Washers
• (2) Axle “R” Clips
Procedure:
Before mounting, note that one end of the axle
holder in the center of each wheel is longer than
the other. With the long end of the axle holder
towards the inside, insert a wheel axle pin
through each wheel and wheel leg. Put an axle
washer on the other side, then insert the axle
“R” clip through the hole in the wheel axle pin.
Turn over the assembled legs/bottom shelf,
then use the provided open end wrench to
mount a caster on each caster leg by clockwise
turning the hex nut on the caster into the
threaded hole at the bottom of the leg tube.
Set the assembled legs/bottom shelf upright,
then hold and slightly press the legs downwards
to ensure all the wheels and casters land on
floor. Tighten all the bolts.
6
ATTACH THe LegS To THe BoTTom SHeLf
Parts required:
Bottom shelf (10)
Hardware required:
8 x Screws 1/4" (34)
Align the holes in the brackets
of the caster legs and wheel
legs with the holes in the bottom
shelf (10).
Insert the 1/4" screws (34) through
the holes in each leg bracket,
then through the holes in the
bottom shelf. Leave the screws
loose for now.
bottom shelf
leg assembly
screw
bracket
ATTACH THe Side BArS To THe LegS
Parts required:
2 x Side bars (11)
Hardware required:
8 x Screws 1/4" (34)
Align the four holes in each side
bar (11) with the holes near the top
of each leg assembly.
Insert a 1/4" screw (34) through
each hole in the side bar, then through
the corresponding hole in the leg
assembly. Leave the screws loose
for now.
screw
side bar
ATTACH THe WHeeLS And CASTerS To THe LegS
Parts required:
2 x Casters (8)
2 x Wheels (9)
Hardware required:
2 x Wheel axles (35)
2 x Axle washers (37)
2 x Axle pins (41)
Tools required:
Open end wrench (42)
7
Before mounting, note that one end
of the axle holder in the centre of
each wheel is longer than the other.
With the long end of the axle holder
towards the inside, insert a wheel axle
(35) through each wheel (9) and wheel
leg (6/7). Put an axle washer (37) on
the other side, then insert the axle pin
(41) through the hole in the wheel and
wheel axle.
Turn over the assembled legs/bottom
shelf, then use the provided open
end wrench to mount a caster (8)
on each caster leg (4/5) by clockwise
turning the hex nut on the caster into
the threaded hole at the bottom of
the leg tube.
caster leg
caster
wheel leg
axle
“r”clip
axle
washer
long end
of axle holder
wheel axle
wheel
Set the assembled legs/bottom shelf upright, then hold and slightly press the legs
downwards to ensur
r. Tighten all the screws
.
MOUNT THE LEGS ON THE GRILL
Parts required:
Grill (1)
Hardware required:
4 x Nuts 1/4
"
(36)
4 x Flat washers 1/4
"
(38)
4 x Spring washers 1/4
"
(39)
4 x Bolts 1/4
"
(40)
Tools required:
Open end wrench (42)
Take the porcelain grill (16) and grease
drain pan (17) out of the grill (1), if you
haven’t already done so.
flat
washer
spring
washer
nut
grill
bolt
Place the grill on the legs. NOTE: The two wheel legs should be at the same side as the
paddle vent (15).
After aligning the holes in the grill and the legs, insert a 1/4" bolt (40) through each leg
tube, then through the grill.
Put a 1/4" flat washer (38) and a 1/4" spring washer (39) on each bolt inside the grill,
then put on a 1/4" nut (36) and tighten it.
pin
leg support
bracket
