background image

20 

extinguished by applying baking soda or salt 
directly onto the flame tamers. Always protect 
your hands when handling anything near the 
cooking surface of the barbecue and  take care 
to protect yourself from the flames.  

 

If a fat fire occurs, please see the instructions 
given below. 

 

Fat Fires 

Empty and clean the 

drip tray and drip pan (and 

foil liner, if applicable) 

of food debris after each 

cooking session. If the barbecue is to be used for 
large gatherings, it will be necessary to turn off 
and  cool the  barbecue  every two  hours to 
remove food debris from the 

drip tray and drip 

pan

 

(and foil liner, if applicable), 

and clean it 

out. The time between cleaning may need to be 
reduced  if  very  fatty  foods  or  cheap  meat 
products are being cooked.  Failure to do this 
may result in a fat fire, which may cause injury 
and could seriously damage the barbecue. 

 

In the event of a fat fire: 

• 

If safe to do so, turn all control knobs to the 
‘off’ position. 

• 

Turn off the gas supply at the gas bottle. 

• 

Keep everyone at a safe distance from the 
barbecue and wait until the fire has burnt 
out.  

• 

Do not close the hood or lid of the barbecue.   

• 

NEVER  DOUSE  A  BARBECUE  WITH 
WATER. IF AN EXTINGUISHER IS USED, 
IT SHOULD BE A POWDER TYPE. 

• 

DO NOT REMOVE THE DRIP TRAY. 

• 

If the fire does not seem to be abating or 
appears to be worsening, contact your local 
Fire Brigade for assistance. 

 

End of Cooking Session 

After each cooking session, turn the barbecue 
burners to the “high” position and burn for 5 
minutes. This procedure will burn off cooking 
residue,  thus making  cleaning  easier.  Make 
sure the hood

 

or lid is open during this process.  

 

Turning Off Your Barbecue 

When you have finished using your barbecue, 
turn all the control valves fully clockwise to the 
“Off” position, then switch off the gas supply at 
the bottle.  
 
Wait  until  the  barbecue  is  sufficiently  cool 
before closing its hood. 

Care and Maintenance 

 

Regularly clean your barbecue between uses 
and  especially  after  extended  periods  of 
storage.  Ensure  the  barbecue  and  its 
components  are  sufficiently  cool  before 
cleaning. Do not leave the barbecue exposed to 
outside weather conditions or stored in damp, 
moist areas. 
 

n

Never  handle  hot  parts with unprotected 
hands. 

n

Never douse the barbecue with water when 
its surfaces are hot. 

 
In order to extend the life and maintain the 
condition  of  your  barbecue,  we  strongly 
recommend that the unit be covered when left 
outside for any length of time, especially during 
the winter months. Heavy-duty barbecue covers 
and other accessories are available from your 
local stockist.  
 
Even when your barbecue is covered for its 
protection, it must be inspected on a regular 
basis as damp or condensation can form which 
may result in damage to the barbecue. It may 
be  necessary  to  dry the  barbecue  and  the 
inside of the cover. It is possible for mould to 
grow  on any fat  remaining  on parts of  the 
barbecue. This should be cleaned off smooth 
surfaces with hot soapy water. 
  
Any rust that is found that does not come into 
contact with the food should be treated with a 
rust inhibitor and painted with barbecue paint or 
a heat resistant paint.  
 

Cooking Surfaces & Warming Rack 

When the barbecue has cooled, clean with hot 
soapy water. To remove any food residue, use 
a mild cream cleaner on a non-abrasive pad.  
Do not use scouring pads or powders as they 
can permanently damage the finish. Rinse well 
and dry thoroughly. Due to the weight of the 
cooking  surfaces,  we  do  not  recommend 
cleaning in a dishwasher. 
 

Burner

  

Provided that they are operating correctly, in 
normal usage,  burning  off  the  residue  after 
cooking will keep the burners clean.  
 
The burners should be removed and cleaned 
annually, or whenever heavy build-up is found, 
to ensure that there are no signs of blockage 

Содержание MF4493

























Отзывы: