Ositech comm 28800 Скачать руководство пользователя страница 80

Страница: 80 / 86

5 - 2

Trumpcard 14400/28800 Modem

Section Five

Local Modem Self-Test

To run a local self-test:

1. Put the Modem into interactive or local mode. Refer to the

communications software manual for this information.

2. Enter

AT [ENTER]

. The Modem will respond with

. If you cannot

see the letters you entered, the local Modem echo is OFF. To turn on
the local Modem echo, enter

ATE1 [ENTER]

If double characters appear on the screen, both the Modem and

software are set to local echo ON. To set the Modem to local echo off,
enter

ATE0 [ENTER].

appears on your screen in place of

, the numeric form result

codes have been enabled. To select textual result codes, enter

ATV1

[ENTER]

. The Modem will respond with

If the Modem does not respond:

•

Ensure that the communications software setup procedure
was run after the Modem was installed. Setup must be run
each time the Modem is installed.

•

Check that the COM port address of the serial port is identical
to the software COM port assignment.

Содержание 28800























































































Результаты поиска

Содержание 28800

Отзывы:

Бренды по названию

Популярные бренды

Ositech comm 28800, Руководство пользователя и справочник

Результаты поиска

Содержание 28800

Отзывы:

Бренды по названию

Популярные бренды