background image

MSG-A • MSG-D OPERATOR INSTALLATION GUIDE

- 36 -

By signing this installation checklist, I/we hereby certify that each item listed and checked above has been covered by the
installer and is clearly understood by the customer.

______________________________________________

_____________________________

Customer Signature

Date

______________________________________________

_____________________________

Installer Signature

Date

GATE OPERATOR INSTALLATION CHECKLIST

1. The gate has been checked to make sure it is level and moves freely in both directions.

2. Potential pinch areas have been guarded so as to be inaccessible 

OR

 have contact and/or

non-contact obstruction sensing devices installed.

3. The installer has installed one or more contact or non-contact obstruction sensing devices, in

compliance with UL325 requirements for this installation.

4. If pedestrian traffic is expected, a separate pedestrian  gate has been installed, a minimum of

seven feet from the gate. The customer has been informed that all

 

pedestrian traffic must use

the pedestrian gate.

5. Warning signs have been installed on each side of the gate in highly visible locations. The

customer has been informed that these signs must remain at all times.

6. There are no controls installed on the gate operator, or within seven feet of the gate.

7. The installer has properly adjusted the obstruction sensing feature and has tested the gate to

make sure that the gate stops and reverses a short distance with minimal resistance applied
(40 lbs. on a swing gate at the end of the gate, 75 lbs. on a slide gate)

8. The installer has instructed the customer in the proper use of the gate operator and reviewed

all of the operational functions, obstruction sensing devices, warning beeper and reset, etc.

9. The installer has instructed the customer in the proper use of the operator’s manual discon-

nect feature. The manual disconnect must never be used while the gate is in motion. The
power switch must be turned off before using the manual disconnect and disengaging the
operator.

10. The installer has reviewed all safety instructions with the customer, and has left the safety

instructions and owner’s information sheets for their reference.

11. The installer has answered any questions the customer has regarding the operation of the

gate operator and gate operator safety precautions.

12. The installer has explained to the customer that a regular maintenance schedule for both the

gate and the gate operator is recommended.

________   ________

________   ________

________   ________

________   ________

________   ________

________   ________

________   ________

________   ________

________   ________

________   ________

________   ________

INSTALLER

CUSTOMER

________   ________

Содержание MSG-A





































Отзывы: