background image

13

12

The casing around the power supply 

must not be damaged

.

 Do not apply any 

heavy weight or pressure on the casing 

to prevent from damage and inury.

Method of usage

Method of usage

4.Turn off power, stop massage

Diagram of the switch position of power supply

Power switch method map

WARNING

1) 

Press power button during massage progress, all massage function will be stop

 

immediately, the backrest and footrest will return to original position automatically,

 

meanwhile you can set up memory function. 

2) 

Memory

 

function: A

t the end of the massage you can store your favorite massage 

combination in memory by pressing the M1 or M2 button for 3 seconds until you 

hear a beep. 

3)After the you hear the beep turn the chair off.

Open the master carton, take down the calf rest. (figure 1)
Remove the back cushion (note: please ensure the heat wire in the cushion was

    unplugged before remove). (figure 2)

Figure 1

Figure 2

Remove the back pad. Make sure that the power connection to the heating pads 

are disconnected before removing the back pad ans shown in Figure 2. Then 

proceed to unzip the backrest cover shown in Figure 3.

At the front of chair remove the leg-rest plastic plate as shown in Figure 4. Pull 

on the plastic connector to disengage. 

Figure 3

Figure 4

Pull

remove 

the 8 screws of front 

front plate

 

as shown in Figure 5.

Open the front 

plate and 

unplug the air 

hose

 and power

 cables that feed to the 

armrest.

 (figure 6)

Figure 5

Figure 6

5.Armrest disassembly 

instructions

Note: Use the correct tools to disassemble and carefully follow the instructions 

below.

Disconnect the 

legrest from the chair. There are 2 air hose connections and 2 

electrical wires.  Be sure the connectors are NOT damaged. Have the chair in the 

reclined position as shown in Figure 1.

Function

Button

Description

Calf rise 
and drop

Backrest rise 

and drop

Leg

rest lifting butto

n. P

press this button

 to raise the legrest.  

Release the button and the legrest will stop.

Legrest lift button. Press this button to lower the legrest.

Press this button to raise the backrest.

Press this button to recline the backrest.

USB

3.USB recharging function and lie-down function.

ON/OFF

Switch

Press to

 turn on and off the massage chair

.

USB recharging por

t is located on the right hand side when 

sitting in the chair. 

 

Содержание TP-8500












Отзывы: