Osaka
-
F 10
- User Manual - V1 - PAG. 2
1.2 Front panel pescription
F 10
set
Aux
1
2
3
4
5
9
7
8
6
1.
set
:
Used for setting the Set point (short press) and for pro-
gramming the function parameters (pressed for 5 s). In pro-
gramming mode is used to enter in parameters edit mode
and confirm the values. In programming mode
set
can be
used together with the key to change the programming
level of the parameters. When the keyboard is locked, the
keys
set
and used together (hold pressed for 5 s), unlock
the keyboard.
2.
/
:
In programming mode is used for decreasing
the values to be set and for selecting the parameters. If
programmed using the
tFb
parameter, when it is pressed
for 1 s during normal operation mode, it can perform other
functions such as the selection of eco mode and so on (see
“Functions of keys and /
”).
3.
/
:
In normal mode (pressed for 5 s) can be used to
start/stop manual defrosting
(
)
. In programming mode is
used for increasing the values to be set and for selecting the
parameters. In programming mode can be used together
with
set
key to change parameters level. Pressed together
with the
set
key for 5 s allows the keyboard unlock.
4.
:
Used (short press) for displaying the instrument vari-
ables (measured temperatures etc.). In programming mode
can be used to return in normal mode (hold for 2 s).
If programmed using the
tUf
parameter, when it is pressed
for 1 s during normal operation mode allows to turn
ON/OFF
(Stand by) the
control action
or other functions like the
Aux
input control etc. (see “Functions of keys and /
”).
5. LED dp/Stand by:
When the instrument is placed in Stand
by mode, this is the only lighted LED. During the normal
operation is the decimal point In programming mode, while
the parameter code is displayed, the dot indicates the
parameter protection level:
not protected
(lit up),
protected
(flashing) and
hidden
(turned OFF).
6. LED
: Indicates the output status (compressor or temper-
ature control device) when the instrument is programmed
for
cooling operation
;
ON
(lit up),
OFF
(turned OFF) or
inhibited
(flashing).
7. LED :
Indicates the output status (compressor or tempera-
ture control device) when the instrument is programmed for
heating operation
;
ON
(lit),
OFF
(turned OFF) or
inhibited
(flashing).
8. LED :
Indicates the
alarm status
:
ON
(lit),
OFF
(turned
OFF) or
silenced
(flashing).
9. LED :
Indicates that the
defrost
is
in progress
.
2. PROGRAMMING
2.1 Fast Set point programming
The normal mode to program the setpoint is done by momen-
tarily pressing the
set
key, the display shows
SP
(or
SPE
) alter-
nated to the programmed value.
To change it press the key to increase the value or to
decrease it
These keys increase or decrease the value one digit at a time,
but if the button is pressed for more than one second the value
increase or decreases rapidly and after two seconds the speed
increases even more in order to quickly reach the desired value.
However, through
ted
parameter you can determine if and
which Set point can be set with the
set
key rapid procedure.
The parameter can have the following values:
oF
SP/SPE cannot be changed with the
set
key rapid procedure
(pressing/releasing the
set
key, nothing happens);
1
Only SP can be set with this procedure (“normal” Set Point);
2
Only SPE can be set with this procedure (“economic”/Eco
Set Point);
3
Both SP and SPE can be set with this procedure;
4
To select the Active Setpoint (SP or SPE).
For example, in case the parameter
TEd
=
1
or
3
, the procedure
is the following:
Press and release the
set
key, the display shows
SP
alternated
to the Set Point value. To change the Set Point, press the
key to increase the value or to decrease it
If only Set Point 1 is present (
TEd
=
1
), once the desired value
is set, press the
set
button to exit the fast programming mode.
If also the “Economic” Set Point (
TEd
=
3
) can be set, pressing
and releasing again the
set
button the display shows
SPE
alter-
nated to its programmed value.
To change the value use the and keys as for the
SP
Set
Point value. Once the desired value is correctly set, press the
set
button to exit the fast Set Point change.
To exit the fast Setpoint programming mode push the
set
key
after the last Set Point has been displayed or pressing no but-
tons for about 10 s, after which the display returns to normal
operation.
2.2 Standard mode parameters programming
To access the instrument function parameters when password
protection is disabled, press the key
set
and keep it pressed for
about 5 seconds, after which the display shows the code that
identifies the first programmable parameter
The desired parameter can be selected using the / keys,
then, pressing the
set
key, the display shows the parameter code
alternated to its value that can be changed with the and
keys.
Once the desired value has been set, press the key
set
again: the
new value is stored and the display shows only the code of the
selected parameter
Pressing the and keys, it is possible to select another
parameter and change it as described.
