ORTILEB KSFB 26/100 Скачать руководство пользователя страница 9

Страница: 9 / 16

2. Product description

Ortlieb Präzisionssysteme GmbH & Co. KG • Jura Str. 11 • 73113 Zell u. Aichelberg • Germany

Tel.: +49 (0) 7164 79 70 1-0 • Fax.: +49 (0) 7164 79 70 1-51 • e-mail: [email protected] • www.ortlieb.net

2.4 Check run-out

To provide best possible run-out results, it is necessary to adjust the clamping device. Therefore

loose the mounting screws between chuck and machine spindle. Check the TIR with a dial

indicator in the taper of the pressure sleeve. After adjusting the chuck, do not forget to retighten the

mounting screws with the proper torque.

TIR-check acc. DIN 6343

2.5 Change the collet

Loose nut-lock screw about 180°

Turn bayonet nut about 60°

Remove collet

Clean the collet-carrier, regrease slightly

Insert collet

Attach the bayonet nut, make sure it locks

Retighten the nut-lock screw

Important:

Please pay attention to a clean collet-carrier, free of dirt and chips, especially when the collet is

changed. Only use intact, clean and slightly greased collets. Before operation, make sure the nut-

lock screw is tightened and the bayonet nut cannot get loose!

Do not operate the chuck without a bayonet nut mounted. The safety screw to prevent rotation

to the pressure sleeve might get damaged.

Содержание KSFB 26/100

















Результаты поиска

Содержание KSFB 26/100

Отзывы:

Похожие инструкции для KSFB 26/100

Бренды по названию

Популярные бренды

ORTILEB KSFB 26/100, Техническая документация инструкция

Результаты поиска

Содержание KSFB 26/100

Отзывы:

Похожие инструкции для KSFB 26/100

Бренды по названию

Популярные бренды