Orion Sentry HP Скачать руководство пользователя страница 9

Страница: 9 / 12

Bulletin #: V113018-04

Issue Date: November 30, 2018

Orion Packaging Systems * A division of Pro Mach

4750 County Road 13 NE Alexandria, MN 56308

(800) 333-6556

http://www.orionpackaging.com/parts-and-service/manuals/

Page 9 of 12

Sentry HP/LP

Quick Start Guide

Adjusting Wrap Settings



To adjust the wrap setting, you must be logged in. Press the login button in the bottom left corner of

the screen



Enter the password then press the checkmark, then X to close the keypad.



Press the Wrap Settings button to display the Wrap Settings Screen.



Press the Top Wraps button to set the number of top wraps applied to the load. Parameters are 1-20.



Press the Bottom Wraps button to set the number of bottom wraps applied to the load. Parameters are

1-20.



Press the Carriage Up Speed % button to change the speed of the carriage on the upward move, in

terms of percentage. Min - 5% Max - 100% The slower the move, the more film overlap on the load.



Press the Carriage Down Speed % button to change the speed of the carriage on the downward

move, in terms of percentage. Min - 5% Max - 100% The slower the move, the more film overlap on
the load.



You may choose more advanced wrap settings for Wrap Direction, Speed Selection, and Autoheight

or Film Fault Enable/ Disable. See your manual for more information on these wrap setting
adjustments.

Illustration 9 – Wrap Settings Screen

Содержание Sentry HP













Результаты поиска

Содержание Sentry HP

Отзывы:

Похожие инструкции для Sentry HP

Бренды по названию

Популярные бренды

Orion Sentry HP, Быстрый старт

Результаты поиска

Содержание Sentry HP

Отзывы:

Похожие инструкции для Sentry HP

Бренды по названию

Популярные бренды