background image

Golden Power #6F22; New Leader #6F22; Gold Peak #6F22; Eveready #522, #1222.; Golden Power G6F22; 

Golden Power GL6F22A 

IMPORTANT! 

Actual battery service life depends on the Alarm and the environment in which it is installed. All the batteries 

specified above are acceptable replacement batteries for this unit. Regardless of the manufacturer’s suggested 

battery life, you MUST replace the battery immediately once the unit starts “chirping” (the “low battery 

warning”). 

To replace the batteries: 

1.

 

Use screwdriver to twist out the tamperproof tabs on both sides of 

the alarm

。 

2.

 

Turn smoke alarm counterclockwise to detach it from the mounting 

plate.  

3.

 

Open the battery cover and remove the battery from the 

compartment.  

4.

 

Press and hold Test/Hush bottom for 10s and then release it. 

5.

 

Insert a new 9-volt battery to compartment. NOTE POLARITY OF 

CONNECTIONS. Ensure the metal tab is fully depressed when the battery has been fitted. 

6.

 

Close the battery cover. 

7.

 

Using Test button, test the alarm to verify 9V DC battery. See “TESTING THE SMOKE ALARM for 

details 

8.

 

Reattach the alarm to the mounting plate by turning alarm clockwise until it snaps into place. Insert the 

tamperproof tabs back into the notch on edge of alarm after alarm is properly positioned in base 

9.

 

Test the alarm using “Test” button. See TESTING THE SMOKE ALARM” for details. 

IF YOUR SMOKE ALARM SOUNDS 

RESPONDING TO AN ALARM 

WARNING! 

 

If the unit alarms and you are not testing the unit, it is warning you of a potentially dangerous 

situation that requires your immediate attention. NEVER ignore any alarm. Ignoring the alarm may 

result in injury or death. 

 

Never remove the batteries from a battery operated Alarm to stop an unwanted alarm (caused by 

cooking smoke, etc.). Removing batteries disables the alarm so it cannot sense smoke, and removes 

your protection. Instead open a window or fan the smoke away from the unit. The alarm will reset 

automatically. 

 

If the unit alarms get everyone out of the house immediately. 

WHAT TO DO IN CASE OF FIRE 

 

Don’t panic; stay calm. Follow your family escape plan. 

 

Get out of the house as quickly as possible. Don’t stop to get dressed or collect anything. 

 

Feel doors with the back of your hand before opening them. If a door is cool, open it slowly. Don’t open 

a hot door. Keep doors and windows closed, unless you must escape through them. 

Содержание VST-WS588IH











Отзывы: