HL-14041-3
O P E R A T I N G M A N U A L
Motorized Actuator Driver
DC power input
Built-in controller type
LSD-KD
Thank you for purchasing an Oriental Motor product.
This Operating Manual describes product handling procedures and
safety precautions.
•
Please read it thoroughly to ensure safe operation.
•
Always keep the manual where it is readily available.
1
Introduction
•
Only qualified personnel should work with the product. Use the
product correctly after thoroughly reading the separate manual
BEFORE USING THE PRODUCT.
The product described in this manual has been designed and
manufactured for use in general industrial equipment. Do not use
for any other purpose. Oriental Motor Co., Ltd. is not responsible
for any damage caused through failure to observe this warning.
•
The driver model
LSD-KD
is a driver common to the
DG
Ⅱ
Series and
EAS
Series.
Operating manual types
Operating manuals for the Motorized Actuator Driver DC power
input FLEX Built-in controller type are listed below.
Use the product correctly after thoroughly reading the operating
manuals.
Operating Manual name
EAS
Series
DG
Ⅱ
Series
BEFORE USING THE PRODUCT
Supplied with
the product
−
DG
Ⅱ
Series Actuator Edition
OPERATING MANUAL
−
Supplied with
the product
EAS
Series OPERATING MANUAL
Supplied with
the product
−
EAS
Series
CHECKING THE PRODUCT
Supplied with
the product
−
Motorized Actuator Driver
DC power input FLEX
Built-in controller type
LSD-KD
OPERATING MANUAL
(this document)
Supplied with
the product
Supplied with
the product
AR
Series FLEX DC power input
Built-in Controller Type
USER MANUAL
∗
−
−
∗
The USER MANUAL for this product is in common with the
AR
Series.
This manual does not come with the product. For details, contact your
nearest Oriental Motor sales office.
CE Marking
•
Low Voltage Directives
Because the input power supply voltage of this product is 24 VDC, it
is not subject to the Low Voltage Directive but install and connect
this product as follows.
•
This product is designed and manufactured to be installed within
another device. Install the product in an enclosure.
•
For the driver power supply, use a DC power supply with
reinforced insulation on its primary and secondary sides.
•
EMC Directive
This product has received EMC compliance under the conditions
specified in "Example of actuator and driver installation and wiring"
on USER MANUAL. Since the compliance with the EMC Directive
of the customer's equipment will be affected by various conditions
such as the configuration, wiring and layout of the control system
devices and electrical parts used together with the actuator and
driver, the customer finally must verify the conformance of the
equipment by performing EMC Testing.
•
Applicable Standards
EMI
Emission Tests
Radiated Emission Test
EN 61000-6-4
EN 61800-3 C3
EN 55011 group 1 class A
EMS
Immunity Tests
Radiation Field Immunity Test
Electrostatic Discharge Immunity Test
Fast Transient / Burst Immunity Test
Conductive Noise Immunity Test
EN 61000-6-2
EN 61800-3 C3
IEC 61000-4-3
IEC 61000-4-2
IEC 61000-4-4
IEC 61000-4-6
•
Machinery Directive (
EAS
Series only)
The motorized actuators and drivers have been designed and
manufactured to be installed within general industrial equipment,
and a Declaration of Incorporation of Partly Completed Machinery is
issued with them according to the Machinery Directive.
Applicable standards: EN ISO 12100
Noise level: 72 dB
Hazardous substances
RoHS (Directive 2002/95/EC 27Jan.2003) compliant
Precautions for use
This section covers limitations and requirements the user should
consider when using the product.
•
Motor excitation at power ON
The motor used in this product is excited when the power is turned
on. If the motor is required to be in non-excitation state when turning
on the power, assign the C-ON input to the input terminal (IN0 to
IN7).
•
Preventing electrical noise
Refer to USER MANUAL for the noise elimination measures.