1
Introduction
Before using the product
Only qualified personnel of electrical and mechanical engineering should work with
the product. Use the product correctly after thoroughly reading the section "Safety
precautions." In addition, be sure to observe the contents described in warning, caution,
and note in this manual.
The product described in this manual is designed and manufactured to be incorporated in
general industrial equipment. Do not use for any other purpose. Oriental Motor Co., Ltd. is
not responsible for any compensation for damage caused through failure to observe this
warning.
Safety precautions
The precautions described below are intended to ensure the safe and correct use of the
product, and to prevent the user and other personnel from exposure to the risk of injury.
Use the product only after carefully reading and fully understanding these instructions.
WARNING
Handling the product without observing the instructions
that accompany a "WARNING" symbol may result in serious
injury or death.
CAUTION
Handling the product without observing the instructions
that accompany a "CAUTION" symbol may result in injury or
property damage.
Note
The items under this heading contain important handling
instructions that the user should observe to ensure safe use
of the product.
WARNING
•
Do not use the product in explosive or corrosive environments, in the presence of
flammable gases or near combustibles. Doing so may result in fire, electric shock, or
injury.
•
Only qualified and educated personnel should be allowed to perform installation,
connection, operation and inspection/troubleshooting of the product. Handling by
unqualified and uneducated personnel may result in fire, electric shock or injury.
•
Do not transport, install, connect, or inspect the product while the power is supplied.
Always turn off the power before carrying out these operations. Accidental contact may
result in electric shock.
•
The motor is Class
Ⅰ
equipment. Install the motor so that it is out of the direct reach of
users, or ground if users can touch it. Failure to do so may result in electric shock.
•
Always keep the power supply voltage within the specified range. Failure to do so may
result in fire or electric shock.
•
Securely connect and ground in accordance with the connection diagram. Failure to do
so may result in fire or electric shock.
•
Do not forcibly bend, pull, or pinch the cable or lead wires. Doing so may result in fire or
electric shock.
•
Turn off the power in the event of a power failure. Otherwise, the motor may suddenly
start when the power is restored, causing injury or damage to equipment.
•
Do not disassemble or modify the motor. Doing so may result in electric shock or injury.
CAUTION
•
Do not use the motor beyond the specifications. Doing so may result in electric shock,
injury, or damage to equipment.
•
Do not touch the motor while operating or immediately after stopping. The surface of
the motor is hot and it may cause a skin burn(s).
•
Do not lift up the product by holding the output shaft, the cable, or the lead wires. Doing
so may result in injury.
•
Do not touch the motor output shaft (shaft end or pinion) with bare hands. Doing so
may result in injury.
•
Keep the area around the motor free of combustible materials. Failure to do so may result
in fire or a skin burn(s).
•
Do not leave anything around the motor that would obstruct ventilation. Doing so may
result in damage to equipment.
•
The motor does not have a built-in overheat protection device. Provide a protection
device externally.
•
When installing the motor in equipment, exercise caution not to pinch your fingers or
other parts of your body between the product and equipment. Injury may result.
•
Do not touch the rotating part (output shaft) while operating the motor. Doing so may
result in injury.
•
Securely install a load to the output shaft. Inappropriate installation may result in injury.
•
When an abnormality is generated, turn off the power immediately. Failure to do so may
result in fire, electric shock, or injury.
•
The motor surface temperature may exceed 70 °C (158 °F) even under
normal operating conditions. If the operator is allowed to approach the
operating motor, attach a warning label on a conspicuous position as
shown in the figure. Failure to do so may result in a skin burn(s).
Warning label
HM-9436-2
O P E R AT I N G M A N U A L
Thank you for purchasing an Oriental Motor product.
This Operating Manual describes product handling procedures and safety precautions.
•
Please read it thoroughly to ensure safe operation.
•
Always keep the manual where it is readily available.
K
Ⅱ
S
Series
Induction Motor
200 W
Preparation
Checking the product
Verify that the items listed below are included. Report any missing or damaged items to
the branch or sales office from which you purchased the product.
Motor ........................................................................... 1 unit
(the combination type comes with the motor and gearhead pre-assembled)
Parallel key ................................................................. 1 piece (only for the combination type)
Mounting screw ....................................................... 1 set
(only for the combination type-parallel shaft gearhead)
Hexagonal socket head screw, plain washer, spring washer: each 4 pieces
OPERATING MANUAL (this document) ............ 1 copy
Checking the model name
Check the motor model and the gearhead
model against the model name shown on their
nameplates, respectively.
Tell us the model name, product serial number,
and manufacturing date when you contact us.
The figure shows a product assembled a right-
angle gearhead.
Motor
Gearhead
•
The box (
) in the model name indicates a code representing the power supply voltage.
JS
: Three-phase 200 VAC 50/60 Hz
ES
: Three-phase 220/230/240 VAC 50/60 Hz
EU
: Three-phase 380/400/415 VAC 50/60 Hz
•
The box (
) in the model name indicates a number representing the gear ratio.
z
Combination type-parallel shaft gearhead
Model
Motor model
Gearhead model
7IK200V
3T2-
S
7IK200VGV-
3T2
7GV
BS
z
Combination type-right angle hollow shaft hypoid gear
GV
gearhead
Model
Motor model
Gearhead model
7IK200V
3T2-
RHS
7IK200VGV-
3T2
7GV
RHS
z
Round shaft type
Model
7IK200VAS-
3T2
Information about nameplate
Manufacturing date
Serial number
Motor specifications
Motor model
Gearhead model
Manufacturing date
Serial number
